1. Design a reinforced concrete beam to carry a service dead load of 20 kN/m (including it and service live load of 25 kN/m plus a concentrated service live load of 30 kN shown. fy = 276 MPa, b = d/2, and 28 mm main bars. The beam is to be reinforced in tension The beam is to be reinforced in tension only. Pu = 1.6 PLL 1.8 m A 2 m TITTB 4 m wu = 1.2 WDL + 1.6 WLL C

Q: Q2: The reinforced concrete Isolated T-Beam shown in Figure 2, carried uniform distribution live…

A: wLL = 35 KN/mwDL = 30 KN/mfc' = 28 MPafy = 420 MPa

Q: Situation #2: A properties: Width, b = 400 mm 415 MPa rectangular beam has the following Effective…

A:

Q: A horizontal tension member is to be constructed of two pieces of plastic glued along the incline pq…

A:

Q: Calculate the forces in members BE and BD of the loaded truss. The forces are positive if in…

A: Given data in question  Load  Span member length  To find out  Forces in members BE & BD

Q: Q1// An interior column in a braced frame has the following service load forces and moments causing…

A: Calculate the factored axial load on the column as follows: Pu=1.2wd+1.6wl Here, wd is the dead load…

Q: a) If olow 160 MPa, select the most economical metric wide- flange shape that should be used to…

A: Data given: σallow = 160 MPa Asked: Select most economical metric-wide flange shape Calculate Von…

Q: A W610 x 82 beam of A 36 steel has end reaction of 302 kN and is supported on a plate with a length…

A: Yield Strength :Yield strength of an element is a maximum stress an element or component can bear…

Q: a. Nominal moment capacity of the overhanging portion of the section. b. Depth of the compression…

A: Solution: Givendata: bf = 750 mm tf = 50 mm d = 750 mm bw = 350 mm Mu = 816 kN.m fc' = 20.7 Mpa fy =…

Q: Find the magnitude and direction of the resultant of a system of forces given in Fig.5. 250N 100N…

A: The resultant for the given forces is given by: R=Fx2+Fy2 Where, Fx = Sum of forces along x-axis Fy…

Q: 3-3 A rectangular section with width b=200mm and depth h=450mm is reinforc with 4 16 of HRB400. The…

A: Width (b) = 200 mmDepth (h) = 450 mmReinforcement of concrete = 4 -16 diameter HRB400Design Moment…

Q: 4. The beam shown in figure below (W 410 x 46.1) has continuous lateral support of both flanges. The…

A: As per Bartleby's guidelines we are supposed to answer only first question. Kindly repost other…

Q: See the image below. A hot-rolled I-beam section has yield strength fy = 300 MPa, ultimate strength…

A:

Q: olve for the (singly reinforced) design flexural capacity, in kNm, of the beam shown = 250 mm = 490…

A:

Design criteria for structural loading

The different loads such as loads due to self-weight (dead load) and external loads such as live load, wind loads, seismic load, snow load, and other loads and load combinations that influence the design of a building are called structural loading. The nature of the applied load differs from changes in the location, design, and type of materials used. The design criteria require that structures must be designed and constructed to be able to withstand all load types that are expected to act upon the structure and render its usage for the designated purpose. The structural members such as beams, slabs, columns, and foundations help the structure to withstand the applied load. There are different institutes such as ASCE and ACI that provide building design codes to assure minimum safety requirements and quality of the structures.