1. Connect the circuit (A - connection) shown in Fig (6). 2. Measure the curre nts In, 2, and Is. Also measure the voltages Vab, Vac and V be , list the values in table 1. 3. Conne ct the circuit (Y - connection) shown in Fig (7). 2. Measure the curre nts In, 2, and I3. Also measure the voltages Vab, Vac and V bc , list the values in table 1. 1ka b A2 12 A 1kQ 1ka 1200 13 (A) 20V+ 4700 1000

1. Connect the circuit (A - connection) shown in Fig (6). 2. Measure the curre nts In, 2, and Is. Also measure the voltages Vab, Vac and V be , list the values in table 1. 3. Conne ct the circuit (Y - connection) shown in Fig (7). 2. Measure the curre nts In, 2, and I3. Also measure the voltages Vab, Vac and V bc , list the values in table 1. 1ka b A2 12 A 1kQ 1ka 1200 13 (A) 20V+ 4700 1000

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter33: Single-phase Motors

Section: Chapter Questions

Problem 1PA

See similar textbooks

Similar questions

Q2:For the network of figure ,determine: a-Vc,VB, VE,Ic,VCE and IB b- Determine the net change in Ic if a change in operating condition result in Ico increasing from 0.2µA to 10 µA, VBE drops from 0.7 V to 0.5 V and B increase 25%. c-Determine the net change in Ic if a change in temperature from 25C°-85C°and Ico increasing from 0.2µA to 10 µA, VBE drops from 0.7 V to 0.5 v. 2.2 Kongb uF 510 KOhm 10 UF HH 1 kOhm B=250 10 mv 1.8Kohm
1) For the network shown in the below figure, the value of current needs to be measured in the 10002 by connecting a 502 ammeter between two terminals A and B, find the following: a) The actual value of current. b) The measured value of current. c) The percentage error in measurement. d) The accuracy of measurement. e) Repeat the aboveif a 25002 ammeter is connected between two terminals A and B. f) State your condlusion. ww 2000 n ww 1000 A Ammeter 500 5V 20002
1. FILL IN THE FOLLOWING TABLE ACCORDING TO THE CIRCUIT SHOW. 2. INTERPRET THE VCE AND ICE CHARACTERISTICS ACCORDING TO THE MEASURED VALUES (MAX. 2 or 3 SENTENCE) R 100K R1 33K 2N2222A Vc. Vbb, I Vec Vce l I Vec Vce le Vec Vce | le Vee | Vce le Vec Vce le Vec Vce le Vec Vce le OuA OV 0,2V 0,4V 0,6V 0,8V 1V 1.2V 5uA 0V 0,2V 0,4V 0,6V 0,8V 1V 1.2V 10uA 0V 0,2V 0,4V 0,6V 0,8V 1V 1.2V 15uA OV 0,2V 0,4V 0,6V 0,8V 1V 1.2V 20uA OV 0,2V 0,4V 0,6V 0,8V 1V 1.2V 25uA 0,2V 0,6V 0,8V OV 0,4V 1V 1.2V Ib Vec Vce Ic Vcc Vce le Vec Vce le Vec Vce Ie Vcc Vce Ic Vcc | Vce lc Vcc Vce OuA 1.4V 1.6V 1.8V 2V 3V 4V 5V 5uA 1.4V 1.6V 1.8V 2V 3V 4V 5V 10uA| 1.4V 1.6V 1.8V 2V 3V 4V 5V 15uA 1.4V 1.6V 1.8V 2V 3V 4V 5V 20uA 1.4V 1.6V 1.8V 2V 3V 4V 5V 25uA 1.4V 1.6V 1.8V 2V 3V 4V 5V に
The circuits branch is defined as: Select one: a. a single path in a network, composed of two parallel elements and the node at each end of that element. b. a single path in a network, composed of one simple element and the node at each end of that element. C. a single path in a network, composed of one source and parallel resistor and a node at each end of the elements. d. None of the above.
1. ) Minimize the following DFA using a. Huffman algorithm using Distinct table. For each step draw a separate Distinct table. 0, 1 1 q1 q2 q4 qo 93 1 95 1. 1.
2. Perform the following analysis and calculations on the circuit shown below. Use Kirchhoff's Laws to solve for the unknown currents I1, l2, and Ig. Show ALL calculations! a. To obtain credit, you must label all active and passive device polarities in the diagram, label each loop (and loop direction) you are using. b. To obtain credit, you must show all relevant equations using Kirchhoff's Laws. c. To obtain credit, you must show your system of linear equations in the unknown currents, and clearly demonstrate your matrix method for solving this system of equations. d. For each of the calculations, you must keep 4 digits in your final results for the currents. 40 Ω 15 Volts www. 25 0 WWw 35 Ω 12 Volts
Provide FBD and complete solution
The circuits branch is defined as: Select one: a. a single path in a network, composed of one simple element and the node at each end of that element. b. None of the above. C. a single path in a network, composed of one source and parallel resistor and a node at each end of the elements. d. a single path in a network, composed of two parallel elements and the node at each end of that element. OE Shot by Hisense H12
It is desired to measure the voltage of the R2 load in the circuit given on the side. Find the relative error of the measurement.
subject: Electronic Circuits: Devices and Analysis course code: ECE 421
The diagram shows the circuit used to investigate how the current varies with potential difference for an electrical component P. The circuit contains an ammeter and a voltmeter. P (1)On the diagram. label the ammgter A and the voltmeter Volteter connectel aceross te inal, Ammeter Connected in sertes to the cirevil. (ii) The position of the contact of the potential divider is moved so that the reading on the voltmeter becomes zero. Label this position Z.
The circuits branch is defined as: Select one: a. a single path in a network, comnposed of one source and parallel resistor and a node at each end of the elements. b. a single path in a network, composed of one simple element and the node at each end of that element. Ti C. a single path in a network, composed of two parallel elements and the node at each end of that element. d. None of the above. dows bu LIN