1. Combustion gases enter the nozzle of a jet engine at 3.8 bar and 820°C. The nozzle is well insulated and the gases expand down to an exit pressure of 1.1 bar. Determine the temperature and the velocity of the gases at exit from the nozzle assuming the velocity at inlet is negligible. For the combustion gases take C, = 1.15 KJ/Kg. K and the ratio of specific heats = 1.32 %3D

1. Combustion gases enter the nozzle of a jet engine at 3.8 bar and 820°C. The nozzle is well insulated and the gases expand down to an exit pressure of 1.1 bar. Determine the temperature and the velocity of the gases at exit from the nozzle assuming the velocity at inlet is negligible. For the combustion gases take C, = 1.15 KJ/Kg. K and the ratio of specific heats = 1.32 %3D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Identify if the property of the following steam: Pressure Specific Enthalpy Specific Entropy MPa kJ/kg kJ/kg-K 13 2483 ?
13. During a reversible process, 2.09 kg/s of gas rejects 322.9 kJ/s of heat isothermally at 25.5°C. For this gas, cp = 2.14 kJ/kg K and c, 1.62 kJ/kg K. The initial pressure is 551.7 kPa. Determine the work steady flow of the process in hp if APE = 2.8 kJ/s and AKE = 6.2 kJ/s.
Use the following Data for Nitrogen gas: R= 0.2968 kJ/kg.K, C,=1.0418 kJ/kg.K, C,=0.745 kJ/kg.K, Required: Draw consistent, clear and standard schematic for the problem representing the inlet and outlet conditions and label your schematic with the given operating conditions. Analyze the problem systematically using step-by-step CV energy and mass analyses, state your assumptions (wherever applicable), and determine the following (circle your final answers): (a) The specific volume and density at the inlet and exit of the compressor; (b) The difference in the specific enthalpy between the exit and inlet of the compressor assuming a constant specific heat Cp; (c) The specific heat loss from the compressor;
1
ASEM 12/6/2015 Q1/ A stream of warm water is produced in a steady flow mixing process by combining 1.0 kg/s of cool water at 25 °C with 0.8 kg/s of hot water at 75 °C. During mixing, heat is lost to the surroundings at the rate of 30 kJ/s. What is the temperature of the warm water stream? Assume the specific heat of water constant at 4.18 kJ/kg.K.
Determine the amount of work required to compressed 1.5 kg of air at a pressure of 7 barg. The isentropic index is 1.2 and the air intake is at 1 bar, 200C & RH =65% v) The discharged air is passed through an R134a refrigerant dryer, the temperature of air coming out the dryer is 400C. The air then settles inside a reservoir at a temperature of 25 0C. Determine: The humidity variation throughout the production of compressed air The amount of condensate formed at each stage of the process by using The humidity definition
16. A gas mixture contains hydrogen, nitrogen and carbon monoxide in equal molar proportions. Treating the components of the mixture as perfect gases, determine the gas constant and the ratio of specific heats for the mixture. Calculate the work required to compress 1 kg of the mixture in reversible adiabatic flow through a pressure ratio of 2 from an initial temperature of 15°C when kinetic and potential energy changes are negligible. [Ans. 0.43 kJ/kg K. 1.4, – 82.76 kJ]
During the compression stroke of a certain gasoline engine, the pressure increases from 1.00 atm to 19.0 atm. The process is adiabatic and the air-fuel mixture behaves as a diatomic ideal gas. (a) By what factor does the volume change? Vfinal = Vinitial (b) By what factor does the temperature change? Tinal = Tinitial Assume the compression starts with 0.016 mole of gas at 28.5°C. (c) Find the value of Q that characterizes the process. (d) Find the value of AEnt that characterizes the process. (e) Find the value of W that characterizes the process.
Bottom part only please, Discuss why the petrol engine is irreversible in terms of entropy and work lost due to the spontaneous flow of heat resulting from finite temperature differences.
2) Argon (ideal gas, Cp=0.5203 kJ/kg.K) at 27 ºC, 85 kPa, and 215 m/s enters a diffuser at a rate of 2 kg/s and leaves at 50 ºC. The exit area of the diffuser is 500 cm2. The gas is estimated to lose heat at a rate of 20 kJ/s during this process. Required: Draw a standard and clear schematic of the problem and label the performance of the schematic. Perform step by step energy and mass analyses, state your assumptions and determine the following:a) The exit velocityb) The inlet areac) The inlet pressure of the Argon