1. Calculate the formation volume factor for the gas given below for use at 5000 psig and 194 °F. Component Composition, mole percent Methane Ethane Propane i- Butane n-Butane - Pentane n-Pentane Hexanes Heptanes plus 97.12 2.42 0.31 0.05 0.02 trace trace 0.02 0.06 100.00 Properties of heptanes plus Soecific gravity Molecular weight 0.758 128 Ib/ib mole

Q: 2. Explain in short major engineering difficulties in water treatment process

A: This question is based on water treatment process and the engineering difficulties associated with…

Q: The coefficient of friction is 0.37, what should be the diameter (in mm) of rolls, if pair of rolls…

A:

Q: For diffusivity range of 0.05x10^(-4)<D_AB<1.0x10^(-4) m/s, the system is more likely to be a O A.…

A: Given that :Diffusivity range is given we have to identify the system is more likely to be…

Q: Following is the example of. O a. Orifice meter O b. Flow O C. Flow Pressure meter Rotameter

A: In the given image, the device contains a transparent glass tube that is placed vertically.  In this…

Q: B/ Define the Schmidt number, Prandtl number and Reynolds number and clear up the relation for each…

A: The Schmidt number (Sc), Prandtl number (Pr), and Reynolds number (Re) are dimensionless variables…

Q: Describe the process by which polyethylene molecules resist elongation when an external load is…

A: Polymer, this word itself can define what is polymer. 'Poly' means many and 'mer' means parts. When…

Q: All diffusivities for the three transport processes have the same units. True False

A:

Q: 1. For mild steel, the ultimate tensile strength should be used in the design of the load carrying…

A: As Per Bartleby Multiple Question Guideline, we are supposed to answer only one question. Kindly…

Q: Q/Explain why at constant capillary pressure the saturation of imbibition process is lower than the…

A: Capillary pressure is a quantity in fluid statics. This pressure is natural phenomena. This pressure…

Q: Which of the following is correct about temperature changes value? Δ°C = Δ°F Ο Ο Δ°C = Δ°R Ο Δ°F=Δ°Κ…

A:

Q: In the forward multiple effect of evaporator The pressure must be decreased from unit to unit The…

A: Multiple effect evaporator : A equipment which has  a congregation of vessels to boil off the water…

Q: Building including services is maximum for:

A: Actually, the cost of building including services contains labor expenses, materials and supplies…

Q: The two tank systems shown in the figure are in steady state. At 0, the flow rate was suddenly…

A:

Q: on control, with no datum features, can be applied to two or more

A:

Q: What is main objective for Sewage Water Treatment to produce electricity

A:

Q: This type of support has a vertical reaction and a vertical load resisting load (A Unsupported B…

A:

Q: 25- Horizontal wells require

A: Horizontal wells: It is the technique in which oil or gas well is dug at angle at least 8 degrees to…

Q: Which among the following is not a parameter for scaling up stirred vessels? A. Geometric similarity…

A: We have to answer and explain the parameter for scaling up stirred vessels?

Q: lowing the wall at x = B to move in the positive z direction at a steady speed vo. Obtain (a) the…

A:

Q: Answer letter D of the Problem

A: Given that Ti  =15 Cm = 10 kgsP = 0.0622 bar mc = 400 kgs

Q: Explain in detail on the E unsteady state material balance for a suitable system with example.

A:

Q: Why might a column not have a uniform diameter?

A: Diameter of distillation column depends upon different factors because of which it cannot be…

Q: The first material that distills before the temperature stabilizes is called forerun heavy key…

A: Right option is to be selected for the given statements.

Q: (b) The general characteristics of three oil wells selected for artificial lift as production method…

A: Table of 3 well are given.

Q: How is pump impeller size calculated

A: The two industrially used pumps are: Positive displacement (PD) pump and Centrifugal pumps. In a…

Q: What

A: The hydrosphere is combined mass of water on ,above and below surface of earth.

Q: Compare S.I and C.I engines with respect to fuel used

A: CI engine - Compression ignition engine SI engine - spark ignition engine

Q: In the section of a shell and tube exchanger shown on figure 4 the outer diameter of the inner tubes…

A:

Q: Q2/The following data are given for the Gas Field: area=170 acres, net productive thickness-43ft,…

A: 1) initial gas in place first, find bulk volume. now we will find initial gas in place. 2)  gas in…

Q: Measurment of Down-hole pressure gradient helps us identify the gas-oil contact and oil-water…

A: The drilling of oil wells depends on various factors. The depth that is to be dug to reach the oil,…

Q: Identiry elements a) through h) on the phase diagram below. What type of fluid is represented by…

A: Since you have posted a question with multiple sub-parts, we will solve first three sub-parts (here…

Q: Question 26 The FCC stacking is referred to as an ABCABC O True O False

A: We’ll answer the first question since the exact one wasn’t specified. Please submit a new question…

Q: The overall resistance L that describes the composite material shown in the diagram to the side is…

A:

Q: What is main objective for Sewage Water Treatment to produce electricity

A:

Q: With example and figure explain hysteresis, dead zone?

A:

Q: B. Drive the Kremser Equation which used for Algebraic Determination of the Number of Ideal Stages.

A: Kremser equation is basically used in absorption process to dertermine the no of ideal stages.It is…

Q: 8 ft 7 ft 10 ft 45° entry 10 ft 10 ft A B 3 ft 3 ft

A: