1.Calculate D10 and Cu for graph "B". Indicate if the sample is well or poorly graded. Explain youranswerPercent passing by weight4030201006050900500803 212100 50U.S. standard sieve sizes3 1 34 628AM8 10 14 16 20 30 40 50 70 100 140 200B10 5Grain size millimeters1 0.51020300.1405060Cumulative percent retained by weight708090100Review the two graphs in classwork # 10. Calculate D10 and Cu for both graphs (label them "A" and"B"). Indicate if the samples are well or poorly graded. Explain.

Particle size distribution curve is given. We need to calculate D10 and Cu for soil A and B

1. Calculate D10 and Cu for graph "B". Indicate if the sample is well or poorly graded. Explain your answer Percent passing by weight 40 30 20 10 100 50 70 60 90 80 0 500 4 3 100 50 211 1 U.S. standard sieve sizes 3 4 6 A 3 4 1 3 2 T 810 14 16 20 30 40 50 70 100 140 200 B 10 5 Grain size millimeters 1 0.5 O 10 20 30 0.1 40 50 60 Cumulative percent retained by weight 70 80 90 100 Review the two graphs in classwork # 10. Calculate D10 and Cu for both graphs (label them "A" and "B"). Indicate if the samples are well or poorly graded. Explain.

1. Calculate D10 and Cu for graph "B". Indicate if the sample is well or poorly graded. Explain your answer Percent passing by weight 40 30 20 10 100 50 70 60 90 80 0 500 4 3 100 50 211 1 U.S. standard sieve sizes 3 4 6 A 3 4 1 3 2 T 810 14 16 20 30 40 50 70 100 140 200 B 10 5 Grain size millimeters 1 0.5 O 10 20 30 0.1 40 50 60 Cumulative percent retained by weight 70 80 90 100 Review the two graphs in classwork # 10. Calculate D10 and Cu for both graphs (label them "A" and "B"). Indicate if the samples are well or poorly graded. Explain.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Percent Diameter Sieve Size Passing in mm (%) 4 4.760 23 10 2.000 19 40 0.420 18 100 0.149 200 0.074 4 LL PL D10 0.50mm D30 9.50mm D60 27.50mm 5.
The density was identified using the following data were gathered: Mass of container = 3.25 Kg Volume of container = 0.01439 m3 Mass of container + Water = 17.64 Kg Mass of container + Coarse Aggregates = 26.42 Kg what is the value of density?
Calculate the (total tensile strength) of the mitotic tensile strength test for the information in the table below: Time R D mm Load Kn sec 1 60 16 14 2 54 14 3 57 4 52 5 53 6 59 7 50 8 56 9 58 10 55 15.5 16 15 15 17.5 9 19 10 11 15.5 18 14 19 17 21 21.4 25
clear and complete solution please
Coarse aggregate is placed in a rigid bucket and rodded with a tamping rod to determine its unit weight. The following data are obtained:Volume of bucket = 14 LWeight of empty bucket = 9.21 kgWeight of bucket filled with dry rodded coarse aggregate:Trial 1 = 34.75 kgTrial 2 = 34.06 kgMeasureSampleA B CWet Mass (g) 521.0 522.4 523.4Dry Mass (g) 491.6 491.7 492.1Absorption (%) 2.5 2.4 2.3Table P 5 . 9 determine the amount of water required to increase the moisture content of aggregate to reach absorption?5.9 Three samples of fine aggregate have the properties shown in Table Trial 3 = 35.74 kga. Calculate the average dry-rodded unit weightb. If the bulk dry specific gravity of the aggregate is 2.620, calculate thepercent voids between aggregate particles for each trial.
The following table shows the lab results of a sieve analysis and Atterberg limits for an inorganic soil sample. The Grain Size graph is attached. What is the soil USCS Designation symbol? Sieve Sample Passing Sieve Size Size/No. (mm) Percentages 3" 75 100% 3/4" 19 100% No. 4 4.75 45% No. 10 2 35% No. 20 0.850 0.630 No. 40 0.425 22% No, 60 0.250 18% No. 100 0.150 7% No. 200 0.075 3% 0.020 0.002 20% LL 1% PL
Given below is the result of a sieve analysis done on a soil sample. Sieve No. Diameter Percent Passing % 4 4.750 95 10 2.000 89 20 0.850 71 40 0.425 47 60 0.250 21 100 0.150 14 200 0.075 7 Pan --- 0 Determine the value of the coefficient of uniformity. Round off to three decimal places.
Given below is the result of a sieve analysis done on a soil sample. Sieve No. Diameter Percent Passing % 4 4.750 95 10 2.000 88 20 0.850 70 40 0.425 50 60 0.250 21 100 0.150 13 200 0.075 5 Pan --- 0 Determine the value of the coefficient of uniformity. Round off to three decimal places.
From the given data shown in the table below, determine the effective specific gravity of aggregates. Round off to two decimal places.
Explain LAP SPLICING. Illustrate a sample figure about it.
Given below is the result of a sieve analysis done on a soil sample. Sieve No. Diameter Percent Passing % 4 4.750 95 10 2.000 83 20 0.850 69 40 0.425 50 60 0.250 27 100 0.150 13 200 0.075 7 Pan --- 0 Determine the value of the coefficient of uniformity. ROUND OFF TO THREE DECIMAL PLACES. USE STORED VALUES.
Given below is the result of a sieve analysis done on a soil sample. Sieve No. Diameter Percent Passing % 4 4.750 97 10 2.000 82 20 0.850 71 40 0.425 42 60 0.250 27 100 0.150 13 200 0.075 8 Pan --- 0 Determine the value of the coefficient of gradation/curvature. Round off to three decimal places.