1. An 8-cylinder, 4-stroke diesel engine was given a test for 30 minutes. The test results are as follows: Generator Rated Capacity 950 hp 91% Electrical efficiency Fuel quantity Fuel temp Air quantity Atmospheric temperature Exhaust gas temperature Cooling water quantity inlet temperature 30 gal 77 F with SG = 0.922 88600 ft 65 F 750 F 18000 ft 95 F outlet temperature 115 F Conduct an engine heat balance based on the above data.

1. An 8-cylinder, 4-stroke diesel engine was given a test for 30 minutes. The test results are as follows: Generator Rated Capacity 950 hp 91% Electrical efficiency Fuel quantity Fuel temp Air quantity Atmospheric temperature Exhaust gas temperature Cooling water quantity inlet temperature 30 gal 77 F with SG = 0.922 88600 ft 65 F 750 F 18000 ft 95 F outlet temperature 115 F Conduct an engine heat balance based on the above data.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

During coastdown testing of a family passenger car, the following road load drag force characteristic was derived: FRL = 0.392v²+162 Where FRL is given in Newtons, and v, the vehicle speed in m/s. It is desired that the vehicle should have a top speed of 200km/h. Assuming a transmission efficiency of 90%, which of the following engines would be most suitable? Type BMEP (Bar) Maximum Engine Cubic Capacity Speed (rpm) (CC) Normally aspirated SI engine 11 6500 1400 Turbocharged Sl engine 16 6000 950 Normally aspirated Cl engine 8.5 4500 2400 Turbocharged and aftercooled CI 12 4500 1800 engine
As a mechanical engineer, you were asked by your supervisor to monitor the operation of 4-stroke engine; as a result you got the following readings: > Imep = 780 kN/ m2 > Engine speed = 800 rpm > Brake Power 30 kW %3D %3D > nm = 85 % > B/S 0.7 You noticed also, that the inlet valve opens 10° before TDC and closes40° after BDC and it takes 0.0035 second after ignition for the charge to gain maximum pressure. Depending on the above readings, find the following engine parameters: a. The crank angle when the spark occursfor the maximum pressure to be at TDC b. The time period in second of inlet valve opening during one cycle c. The diameter of the engine d. The average piston speed 1 Upload file
Consider an ideal gas with the following characteristics: R = 95 ft-lbf/lbm-R Cp = 0.25 +0.00035T (BTU/lbm-R) Solve for the value of k at 1000 R. Refer to the table shown below: m T1 T3 P1 P2 Carnot cycle 10 lbm 850 deg F 125 deg F 345 psig 150 psig Solve the following unknown parameters for Carnot cycle a. V4 b. QA and QR c. Wnet d. e. e mep
ASAP
Q.4 urDuring the trial of a single-cylinder, four-strok oll engine, the following tesults were obtained. Cylinder diameta Stroke Mean effective pressure Torque Speed Oil consumption Calorific value of fuel Cooling water flow rate Air used per kg of fuel Rise in cooling water tamperat ure Temperature of exhaust gaWN Room tamperat ure Mean spedfie beat of exhoust gw Specifie heat of water 20 an 40 am 6 bar 407 Nm 250 rpm 1 kg/h 13 MJ/kg 1.5 kg/min 30 kg 45 "C 120 C 20 °C I kI/kg K L.I8 kJ/kg K Find the ip.bp and draw upa heat balane sheet for the test in kl/h.
None
Two strokes Cl engine develops a break power of 368 kW while its frictional power is 73.6 kW. Its fuel consumption is 180 kg/h and works with an air-fuel ratio of 20:1. The heating value of the fuel is 42000kJ/kg. Calculate mechanical efficiency? O a. 83.3% O b. 65.2% O c. 91.9% O d. 23.1% Oe. All of the answers are false.
Kindly Show the details of your solutions on PROBLEM #2 with Schematic and TS Diagrams with correct dimension analysis Plsss use metric system unit. Thanksss! ❤️?
17:51 O P Vo) 4G II LTE2 1 ethuto.cut.ac.za/webapps/asse 27 * Question Completion Status: QUESTION 57 The following processes occurs in a reversible thermodynamic cycle: 1-2: Reversible polytropic compression at pressure 0.5 bar at volume 0.08 m3 to a pressure 9.6 bar and specific volume 0.5 m3/kg. The index of compression may be taken as n. 2-3: Reversibly expansion with expansion index of 2 to pressure 1.2 bar. 3-1: Reversible cooling at constant volume to the initial state. Calculate the work for the expansion in the process to 2 decimal places. Not in kilo or mega of unit. Click Save and Submit to save and submit. Click Save All Answers to save all answers. Save All Answers Close Window Save and Submit
Please answer the attached file
Question 11 A 4 stroke gasoline reciprocating internal combustion engine operating stoichiometrically in an environment at standard temperature and pressure consumes 0.8 kilograms of fuel per hour and it has a displacement of 0.77 litres. The engine speed is 2,714 revolutions per minute. Assume the ambient air density is 1.2 kg/m3. What is the volumetric efficiency of the engine. Enter your answer as a rounded percentage. e.g., if the volumetric efficiency is 63.6%, enter the number 64.
ENGINE SPECIFICATIONS: Engine Type : Four cylinder Four stroke Diesel engine, Bore: 0.073m, Stroke: 0.0889m Capacity: 1489cc, Power: 36 H.P. at 4000 rpm, Torque : 8.5 kg.m at 2250 rpm and Compression Ratio :17.3:1 Explain how to measure the :- (i) Fuel consumption. (ii) (iii) Manometer readings for air flow. RPM, power output etc. Study of various components of diesel engine.