1. A uniformly distributed load of 68 Ib/ft is carried by a simply supported beam span. The beam is a hollow rectangular section, having a width, b = 10.1 inches, height, h = 16.8 inches and constant wall thickness of 1.7 inches. Determine the first moment of area, Q of the beam in mm^3 at the point of maximum shearing stress.

1. A uniformly distributed load of 68 Ib/ft is carried by a simply supported beam span. The beam is a hollow rectangular section, having a width, b = 10.1 inches, height, h = 16.8 inches and constant wall thickness of 1.7 inches. Determine the first moment of area, Q of the beam in mm^3 at the point of maximum shearing stress.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A steel pipe (D = 3.500 in.; d = 3.068 in.) supports a concentrated load of P = 617 lb as shown. The span length of the cantilever beam is L = 4 ft. Determine the magnitude of the maximum bending stress in the pipe. O 21.55 ksi O 13.81 ksi O 15.73 ksi O 24.04 ksi O 17.18 ksi L B P d Pipe cross section. D
6.3 Design the beam below using the operating stresses method If the uniformly spread load is n= 10 20 km section width b = 300mm, permissible stresses 140MPa, c=10MPa = ignore the weight of the beam. W-20 kN/m 4m
The beam shown in figure carries a uniformly distributed load of w on overhang BC. The beam is constructed of a wood beam [E,=12 GPa] that is reinforced on its upper surface by a steel plate [E,-200 GPa] plate. Assume that the allowable bending stresses of the wood and the steel are o. = 9 MPa and o = 165 MPa, respectively. Determine the largest acceptable magnitude for distributed load w. [L = 4m, a = 1.25 m, b. =150 mm, d, =280 mm, b. = 230 mm, t, = 6 mm] IC
Determine the minimum width "b" of the beam shown if the flexural stress is not to exceed 13 MPa. Answer must be in mm. Given: a = 1 m, b= 4 m, c = 1 m, P = 7 kN, and w = 4 kN/m. P KN w kN/m cm (not scaled) 220 mm bm a m Ra Ri
1.50 The cylindrical steel column has an outer diameter of 4 in. and inner diame- ter of 3.5 in. The column is separated from the concrete foundation by a square bearing plate. The working compressive stress is 26 000 psi for the column, and the working bearing stress is 1200 psi for concrete. Find the largest force P that can be applied to the column. Į 3.5 in 0.125 in. 0.75 in. 2800 lb 7 in. FIG. P1.50 1.5 in. 6 in.- 14800 lb B FIG. P1.49 6 in.-
2. A uniformly distributed load of 54 Ib/ft is carried by a simply supported beam span. The beam is a hollow rectangular section, having a width, b = 10.5 inches, height, h = 11.2 inches and constant wall thickness of 0.9 inches. Determine the maximum length of the beam in feet if the shearing stress is limited to 82 psi. Assume the load acts over the entire length of the beam.
Need help ASAP Determine the max flexural stress in MPa
Rectangular reinforced concrete beam section b = 40 cm, h = 60 cm, d = 53 cm, material strength fy = 4200 = 4200 kgf / cm^2, fc ' = 280 kgf/cm^2, beam section configuration #4 For closed stirrups @15 cm, the net cover is 4 cm, and the beam section is subjected to a torque of Tu = Tcr. Q: What is the ultimate shear load value Vu that the beam section can bear. Among them, Tcr is the cracking torque of the beam section, #4 steel bar (db=1.27 cm, Ab=1.267 cm^2).
Please answer with explanation. I will really upvote
The extruded plastic shape will be subjected to an internal shear force of V= 355 lb. Dimensions of the cross section are b-1.7 in.d- 3.4 in, c-2.3 in, and t-0.14 in. Determine: (a) the horizontal shear stress at points A and B. (b) the horizontal shear stress at point C, which is located at a distance of yc-1.2 in. below the z centroidal axis. (c) the maximum horizontal shear stress in the extrusion. yc B (typ.)
A T-shape beam is subjected to a vertical shear force of V = 30 kN. The beams centroid is located 211.1 mm above the bottom surface of the beam, and the moment of inertia is l₂ = 48.7 x 106mm4.[b = 178 mm, h = 300 mm, t₁ = 12.7, tw = 9] b h tw Determine the shear stress in the flange at the intersection of the flange and the web. 6.96 MPa 7.6 MPa 2.94 MPa 4.3 MPa 6.09 MPa
A rectangular reinforced concrete beam has a width of 300 mm and an effective depth of 700 mm. It is subjected to a nominal moment of 550 kN-m. If fc = 28 MPa, fy = 280 MPa, and Es = 200 GPa. a. Determine the balance steel ratio in percent; b. Solve for the depth of the equivalent rectangular stress block; c. Check whether the beam is tension-controlled, compression-controlled, or within the transition region and determine the value of the strength reduction factor, ; d.Solve for the ultimate moment capacity of the beam.