1. A tensile load of 5.00 kN is applied to a square bar 12 mm on a side and having a length of 1.65 m. (a) Compute the stress and the axial deformation in the bar if it is made from (i) SAE 1020 hot- rolled steel, (ii) SAE 8650 OQT 1000 steel, (iii) ductile iron A536(60-40-18), (iv) aluminum 6061-T6, (v) titanium Ti-6Al-4V, (vi) rigid PVC plastic, and (vii) phenolic plastic. (b) For each of the case in (a), compute the maximum safe load that can be carried by the bar.

1. A tensile load of 5.00 kN is applied to a square bar 12 mm on a side and having a length of 1.65 m. (a) Compute the stress and the axial deformation in the bar if it is made from (i) SAE 1020 hot- rolled steel, (ii) SAE 8650 OQT 1000 steel, (iii) ductile iron A536(60-40-18), (iv) aluminum 6061-T6, (v) titanium Ti-6Al-4V, (vi) rigid PVC plastic, and (vii) phenolic plastic. (b) For each of the case in (a), compute the maximum safe load that can be carried by the bar.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

450 mm long a ISI 1020 Steel long is subjected to a tensile load of 55 kilo Newton the allowable tensile stress is 140 mega pascal and the allowable total elongation is not to exit 0.2 mm calculate the required rod diameter the proportional limit is 175 megapascal
A bar of dimension 120 mm x 50 mm x 40 mm, is subjected to an axial pull of 50 kN. The measured extension is 0.25 mm and change in depth is 0.0036 mm. Calculate: (i) Young’s Modulus, (ii) Poisson’s ratio (iii) Shear Modulus. and (iv) Bulk Modulus (i) The Young's modulus is (N/mm2) = _________________ (ii) Poisson's ratio = ___________________ (iii) The shear modulus is (unit in N/mm2) = ________________ (iv) The Bulk modulus is (unit in N/mm2) =
Hi, Could i please have the answrs, workings out anf formulas ues for the attached question. Thank you.
A ¼ inch diameter steel rod is to carry an axial load of 2000 lbs. If the yield strength is 38 ksi, will the rod yield?
Calculate the maximum stress of a cylindrical specimen of steel alloy having an initial diameter of 12.55 mm and 110 mm long is pulled in tension with a maximum force of 20 kN. Select one: O a. 61.59 MPa O b. 125.22 MPa O c. 161.68 MPa O d. 160.15 MPa
Determine the material index for a lightweight, stiff axially loaded bar.
Please explain in details thank you !!
Calculate the design stress when a material has an ultimate strength of 120 psi with a factor of safety of 5. Express your answer in Kpa.
Why did it became 4F/A from F/A, in (a)
2. A short compression member with Do = 2Di is to support a dead load of 25 tons. The material is to be 4130 steel, WQT 1100 F. Calculate the outside and inside diameters on the basis of: (a) yield strength, 1 1/4 in (b) ultimate strength. 1 3/4 in For 4130 steel, WQT 1100 F S₂ = 127 ksi N₁ = 4 Sy = 114 ks Ny=2
The bar is made from steel and has an allowable stress of allow = 19.7 ksi (Figure 1) Figure P 1.875 in. 0.75 in. -0.125 in. 1.25 in. r 0.25 in. 1 of 1 Part A Determine the maximum axial force P that can be applied to the bar. Express your answer to three significant figures and include the appropriate units. P = Submit μA Value Request Answer < Return to Assignment Units Provide Feedback ?
Hi could i please have the workings out, formulas and answer to the attached question. Thanks.