1. A square-wave inverter has an R-L load with R 15 2 and L. 10 mH. The inverter output frequency is 400 Hz (a) Determine the value of the de source required to establish a load current which has a fundamental frequency component of 10 A rms. (b) Determine the THD of the load current. (c) Sketch the output and input currents.

1. A square-wave inverter has an R-L load with R 15 2 and L. 10 mH. The inverter output frequency is 400 Hz (a) Determine the value of the de source required to establish a load current which has a fundamental frequency component of 10 A rms. (b) Determine the THD of the load current. (c) Sketch the output and input currents.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

16. The solar array's maximum voltage & Current should be than the inverter's maximum input DC voltage & current a. Lower b. Higher c. Equal
Find the line- to- line voltages and line-to-neutral voltages of three-phase inverter for 180 degree conduction.
Find the distortion factor, for a single-phase half- wave bridge inverter with dc source Vs = 1 kV. O a.1 O b. 0.7 c. 0.9 O d. 0.87
None
B6
QUESTION TWO A single-phase asymmetrical semiconverter feeds an RL load with R = 10 N and a large L so that load current is level. The source voltage is 230 V, 50 Hz. For a firing tingle delay of 30°, determine; (a) average value of output voltage and output current, (b) average and rms values of diode, thyristor and source currents, (c) input power factor and circuit turn-off time.
A three phase inverter below has a Y- connected load. The inverter frequency is fo = 60 Hz and the DC input voltage Vs = 220V. The applied control signal is a 180 deg conduction mode. The RMS Line to Line voltage Vo is equal to 179.63V. The total harmonic distortion (THD) is equal to: Select one: a. 48.34% b. 31.08% c. None of these d. 100%
Problem 2 A square-wave inverter has an RL load with R = 15 2 and L = 10 mH. The inverter output frequency is 400 Hz. (a) Determine the value of the dc source required to establish a load current that has a fundamental frequency component of 8 A rms. (b) Determine the THD of the load current.
Q1) The square-wave inverter has a de input of 150 V and supplies a series RL load with R=20 Q and L = 40 mH. (a) Determine an expression for steady state load current. (b) Sketch the load current and indicate the time intervals when each switch component (Q1, D1;... Q4, D4) is conducting. (c) Determine the peak current in each switch component. (d) What is the maximum voltage across each switch?
A single phase half a bridge bipolar PWM inverter is operated from a center top 240 volts DC supply. The fundamental output frequency is adjusted to 50 Hz, the carrier frequency used is 1.2 kHz, modulation index is adjusted to 0.8. Determine: i) Carrier ratio (Mf) and the number of pulses per cycle. ii) fundamental output voltage. iii) distortion and harmonic factor of the output voltage waveform. vi) Draw the waveforms created O a. 24 O b. 16 O c. 20 O d. 12
for square wave PWM inverter, Vdc=100V, L=25mH, R=1002, f=60Hz. draw the spectrum of the output voltage and current and then find the rms current value and the output power. Take n =1-20.
Question A single-phase full-bridge inverter has a resistive load of 2.4 0 and a source voltage of 48 V. RMS values of the fundamental voltage and output power are respectively and PA