1. A sample of water from a local river is collected for testing. There are three possible contaminants that may be present: lead ions (Pb²+), magnesium ions (Mg2+), and Zinc ions (Zn²+). Using a table, design a series of tests that can be conducted to accurately identify which contaminant ions are present. Be sure to show the results for each test.

1. A sample of water from a local river is collected for testing. There are three possible contaminants that may be present: lead ions (Pb²+), magnesium ions (Mg2+), and Zinc ions (Zn²+). Using a table, design a series of tests that can be conducted to accurately identify which contaminant ions are present. Be sure to show the results for each test.

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

How much water do you need to add to 243 mL of 3.36 M KCl solution to make a 1.0 M solution? (assume the volume of solvent is the volume of solution) Round to the hundredths place. Round all average atomic mass from the periodic table to the whole number.
Lead is a possible contaminant in public water systems. There are many reasons we should be concerned about this, but this may be especially concerning if the water is used for drinking. Removing all lead is not feasible, so many local governments must set an “acceptable” concentration for contaminants. The “acceptable” concentration of lead in public water for some states is 7.2 x 10^-7 M. If 10.00 mL of 1.00 M lead is poured down the sink, how many liters of water are required to make sure the concentration of lead is 7.1 x 10^-7 M, which is just below the acceptable level?
An aqueous solution at 25 °C has a H₂O concentration of 6.2 × 10¯M. Calculate the OH concentration. Be sure your answer has the correct number of significant digits. -7 1.61 × 10 M x10 X Ś
An analytical chemist weighs out 0.159 g of an unknown monoprotic acid into a 250 mL volumetric flask and dilutes to the mark titrates this solution with 0.0700 M NaOH solution. When the titration reaches the equivalence point, the chemist finds she has added 25.2 mL of NaOH solution. Calculate the molar mass of the unknown acid. Round your answer to 3 significant digits. mol
Fill in the blanks by doing the necessary calculations with the information provided. a) pH = 12.3 [H+] = _______________ b) [OH-] = 2.29 x 10-11 [H+] = __________ c) [H+] = 4.07 x 10-7 pH = __________ d) [H+] = 9.93 x 10-4 pOH = ____________
Imagine you are preparing a solution of NaCl and a solution of CaCl2. After you prepare them you go out to lunch with your colleagues. When you come back you cannot remember which solution is in which container because you forgot to label the containers before going to lunch. What experiments can you perform to identify each solution?
You have three sodium carbonate solutions on a lab table in front of you. All of the solutions came from a 500.0-mL volumetric flask containing 3.00 M sodium carbonate.Solution 1 contains 100.0 mL of the 3.00 M solution.Solution 2 contains 50.0 mL of the 3.00 M solution.Solution 3 contains 10.0 mL of the 3.00 M solution.What volume of water (in mL) must evaporate from Solution 1 in order to have a concentration of 4.88 M?
Commercial bleaches typically rely on sodium hypochlorite, NaClO, as the active ingredient. The molarity of a strong commercial bleach solution is 1.12 M. It is recommended that for household sanitizing that you put 10 mL of bleach per liter of water. What is the concentration of the diluted solution? Show your work.
Part 3: What mass of tin was used to make the tin solution? In a similar experiment, a sample of tin metal was dissolved in nitric acid to produce 28.00 mL of solution containing Sn²+. Titration analysis resulted in the calculation that the concentration of Sn²+ in this solution was 0.65 mol/L. b. What mass of tin was used to make the tin solution? Find the mass of the Sn(s) in g: (give your answer to 2 decimal places) Your Answer: Answer
An unknown soil sample contained 0.0587 M of Co²⁺. Convert the concentration from molarity to mg/kg of soil. Be sure to reference the lab manual to ensure you have accounted for all treatments of the soil samples collected.
2. Use print and/or or Internet resources to research ways in which you could test for dissolved lead in drinking water. Design an investigation based on your findings to test the lead content of a given water sample. Describe all necessary safety precautions, including the safe handling and disposal of the lead precipitate.