1. A Resistance temperature detector (RTD) is placed in a bridge circuit shown below with a 10kn potentiometer. The RTD has resistance of 40002 at 22°C and a temperature coefficient (ao) of 0.004/°C. When the potentiometer is adjusted to 3.26 kn, the bridge is balanced. Determine the temperature. 9V 1kΩ 2.14ΚΩ 200Ω RTD a) Determine the output voltage from the galvanometer when the temperature at 375k (potentiometer value is 2.78kohm)

1. A Resistance temperature detector (RTD) is placed in a bridge circuit shown below with a 10kn potentiometer. The RTD has resistance of 40002 at 22°C and a temperature coefficient (ao) of 0.004/°C. When the potentiometer is adjusted to 3.26 kn, the bridge is balanced. Determine the temperature. 9V 1kΩ 2.14ΚΩ 200Ω RTD a) Determine the output voltage from the galvanometer when the temperature at 375k (potentiometer value is 2.78kohm)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

pls make it to 4 decimal places
Question 12 A JFET has a specified pinch-off voltage of 5V. When VGs=0, what is Vos at the point where drain current becomes constant? undefined 5V OV
Let's assume that 0V when A, B, C, D, E switches are open and 1V when they are closed. What will be the V0 output voltage value when the switches are closed in the order in the table? According to this, draw the shape of the A, B, C, D, E and V0 voltages. Comment on how the circuit turned out. Opamp's supply is ± 12V
9 76 minutes 12V R1 3 Vout R2 VREF 5V +888 Volts -12V Determine the output voltage, Vout when: R1=10000, R2=12573 Vref=5V 8. 2.
Determine the output voltage, Vout when : R1= 10000 R2=12818 Vref=5V
5. A surge resistor of 4.7 ohm is added to Figure 4-45 in between the rectifiers circuit and the capacitor. What is the maximum possible value of surge current?
After bridge balance, the value of current in the detector circuit is 5V = O a. same in the bridge current O b. 0 O C. infinite O d. point 1 is more than point 2
According to the use of silicon diode in the circuit, what are the maximum and minimum values of the output voltage?
In Full Bridge arrangement of strain measurement, supply voltage is of 0.5 V and resistance of each arm is 190 ohms. The change in resistance will be 24 ohms and the gauge factor will be 0.5. Find a) output voltage in mV b) strain output voltage in mV Strain
Figure 4 b) Figure 5 shows the silicon base BJT with a Rc = 1 kQ, Rg = 10 k2, Vcc = 11 V, VBB = 6 V, BDC = 99. Determine Ig, Ic, lE, VCE and VCB- Rc 1 ko Vc 10 kn 11 V VBB 6 V Figure 5
Please solve this question early
What is the peak forward current through each diode +50 V +5 V R Vin V out RE V out 47 Ω. 3.3 kN Vin -50 V -5 V (b) (a)