1. A home has a floor area of 1500 ft2 , the following fixed loads 3000 VA for two small appliance circuits and 1500 VA for 100% laundry. two small appliance circuits and 1500 VA for 100% laundry. The appliances are a 12kw stove and a 5.5kw, 240 V dryer. Assume a factor of 70% for both appliances for the neutral calculation. The ambient temperature is 42 c - Calculate general lighting load - Estimate the number of lighting circuits that will be 20A at 120V. - Estimate the number of circuits there will be at 20A at 120 for small appliances and laundry. and laundry. - Calculate TOTAL EFFECTIVE LOAD (VA)

1. A home has a floor area of 1500 ft2 , the following fixed loads 3000 VA for two small appliance circuits and 1500 VA for 100% laundry. two small appliance circuits and 1500 VA for 100% laundry. The appliances are a 12kw stove and a 5.5kw, 240 V dryer. Assume a factor of 70% for both appliances for the neutral calculation. The ambient temperature is 42 c - Calculate general lighting load - Estimate the number of lighting circuits that will be 20A at 120V. - Estimate the number of circuits there will be at 20A at 120 for small appliances and laundry. and laundry. - Calculate TOTAL EFFECTIVE LOAD (VA)

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.31P: Consider two interconnected voltage sources connected by a line of impedance Z=jX, as shown in...

See similar textbooks

Similar questions

Consider Two same size series connected PV modules,each with the specification as Po=100W, Voc= 24.5V and Isc=5A.then choose the correct Statement Refer to this PV Panel. a.The output power from this panel is 100W , the Voltage is 24.5V and the current is 10A b.The output power from this panel is 200W , the Voltage is 24.5V and the current is 10A c.The output power from this panel is 200W , the Voltage is 49V and the current is 5A d.The output power from this panel is 200W , the Voltage is 49V and the current is 10AClear my choice
Why in high voltage system, we prefer direct or small resistance? How to define the classes of load? Why we should to do such classification??(find answer from website) what are the main load curves of the power system? What is the maximum load utilization hours? What are the applications of load curve and annual load curve in the design and operation of power system? (find answer from website)
1. Electrical explosions directly into the face of a person working on or near energizedelectrical equipment can and will cause serious injury or death. OSHA laws and NFPA70E have strict safety requirements for working on electrical equipment. The basicrules are to turn off the power before working on the equipment and to wear the propertype of nonflammable clothing. To further provide safety for the worker, the NationalElectrical Code has a requirement pertaining to arc-flash hazard warning. This requirement is found in of the NEC.
What is the purpose of power factor correction to a given load? O To reduce the amount of voltage to the load. O To reduce the amount of dependence on automated machinery. O To reduce the amount of current to the load. O To reduce the amount of resistance of the load.
(5) Primary AC Source Transformer Secondary AC/DC Full-wave Rectifier Capaictor in Non- linear Load Figure 6 Analyse different methods of harmonics mitigation to eliminate the harmonic, which you have identify in above power system circuit. You can use harmonic filters, K or equivalent transformers or oversized neutral method depending upon the harmonic sources.
A generator operating at 50 Hz delivers 1 p.u. power to an infinite bus through a transmission circuit in which resistance is ignored. A fault takes place reducing the maximum power transferable to 0.5 p.u. Where as before the fault, this power was 2.5 p.u. and after the clearance of the fault, it is 2 p.u. The value of 8 is max
Q10-The full-load copper loss on the H.V. side of 100KVA, 11000/317 V, single-phase transformer is o.62 Kw and on the L.V. side is 0.48 kW. i) Calculate R1 ,R2 in ohms ii) Find X1 ,X2,if the total reactance is 4% ,and the reactance is divided in same proportion as resistance. Ans. (7.52, 0.00482 2 , 27.32,0.175 2)
Question No.14: A peak load on the thermal power plant is 75 MW. The loads having maximum demands of 35 MW, 20MW, 15 MW and 18MW are connected to the power plant. The capacity of the plant is 90 MW and annual load factor is 0.53. Calculate the average load on power plant, energy supplied per year, demand factor and diversity factor.
A voltage multiplier has 12 stages Capacitances, all equal to 0.08 μF. Thesupply transformer secondary voltage is 150 kV at a frequency of 100 Hz. Load current 0,006A.What is the percentage ripple, the regulation and the optimum number of stages for minimumregulation or voltage drop.
A power transmission line of 11kV (maximum) carries a maximum current of 200A is connecting the two areas. A PMMC voltmeter of (0-300V) range and a PMMC ammeter of (0-10A) range are to be used for measurement of voltage and currents of the transmission line. 1.Design and draw a circuit with suitable instrument transformers for the measurement. Use sample values for winding turns. 2.On a particular day, the readings shown by the meters were 7.5A and 240V. Calculate the actual voltage and current in the transmission line.
A generator operating at 50 Hz delivers 1 pu power to an infinite bus through a transmission circuit in which resistance is ignored. A fault takes place. reducing the maximum power transferable to 0.5 pu whereas before the fault, this power was 2.0 pu and after the clearance of the fault, it is 1.5 pu. By the use of equal area criterion, determine the critical clearing angle.
Consider two interconnected voltage sources connected by a line of impedance Z=jX, as shown in Figure 2.27. (a) Obtain expressions for P12 and Q12. (b) Determine the maximum power transfer and the condition for it to