1. A given FM transmitter is modulated with a single sinusoid. The output for no modulation is 200 watts into a 50 2 resistive load. The peak frequency deviation of the transmitter is carefully increased from zero until the second sideband amplitude in the output is zero. Under these conditions determine: (a) The average power at carrier frequency. (b) The average power in all the remaining sidebands. (c) The average power in the third – order sidebands.

Q: Q) The frequency is relating to time period--- Square proportional. O Not related. Directly…

A: In this question Choose the correct options What is relation between frequency and time period.

Q: What are the steps for plotting points on microstation uisng offset, station, side and elevation?

A: We need to tell about steps for plotting points on microstation uisng offset, station, side and…

Q: List the minimum trade size Type EMT for each of the following applications. (Objective 12-1)…

A: As per Bartleby expert policy only first individual question is to be answered. So, answering only…

Q: What spaces are not included in floor area when calculating the load in volt amperes per square…

A: For calculating the load, first evaluated the total floor area. And according to the NEC , the total…

Q: Choose which answers are correct ‎‏What is the unit of slope of a Fuel cost curve ? a . $ / MWh b .…

A:

Q: what is error in mesurement system? Also discuss its types

A: Error is the difference between the true value and measured value of the system. Error = measured…

Q: Fill in the blanks: Q. Expansion of LSB is

A: A combinational circuit is one in which the various gates in the circuit, such as the encoder,…

Q: What can you say/perspective about National Electrical Code?

A: The National Electrical Code (NEC) was created to protect people and property from the risks posed…

Q: Find % Regulation for the given readings VR(Line to Line ) = 394 Volts, Vs(Line to Line ) = 458 %3D…

A:

Q: 8- Generally as of the operating voltage which of the following options are the correct words that…

A:

Q: please tell me last part answer

A: let Z = a+jb  then a is called real part and b is called imaginary part .

Q: What type of terminal seal is shown here?

A: Given: What type of terminal seal is shown in figure?

Q: What is receptacle load ? Explain under 100 words...

A: The amount of load produced by a device inserted into a receptacle is referred to as a receptacle…

Q: Number 23 please.

A:

Q: Find the difference. 11010011two − 1011101two _____two

A: We will first convert the given binary numbers into decimal. The subtraction of these decimal…

Q: 6- What is meant by one decade, and one octave?

A: We need to define decade and octave

Q: QI-a-Draw the Pollution Control Equipment's. That used for dust as continuous way with diameter 1000…

A: DIFFERENT POLLUTION CONTROL EQUIPMENT'S THAT ARE USED FOR DUST AS CONTINUOUS WAY AND THEIR PURPOSE…

Q: For The Volfage-divider bias configurafion of the hgure Shown below, determine: Vc ,VE B IBQ. I ca,…

A:

Q: ________________________ is the measure of reproducibility a. Accuracy b. Repeatability c.…

A: Electrical circuits involve the measuring of different variables. The measurement of any variable…

Q: 2. Explain over modulation.

A:

Q: HERE IS IT

A: Physical address can be expressed by the following formula:Physical Address = (Segment Address) x 10…

Q: Which is easier to use a bnc connector or sma connector

A: BNC are bigger and easier and faster to handle. SMA are quite a bit higher in frequency capability…

Q: Q6) Explain by drawing a block diagram of a power supply?

A: Draw the block diagram of the Regulated power supply.

Q: 110 About indistrial piping WHY IS THE ASME 31.3 ALLOWABLE VOLTAGE A COMBINED VOLTAGE?

A: According to the question, WHY IS THE ASME 31.3 ALLOWABLE VOLTAGE A COMBINED VOLTAGE?

Q: The circuit shown in Figure Q5.1 consists of a current source connected to a load via a cable. The…

A: Given circuit is - Value of current source is -

Q: What is meant by Electric Bid Package?

A: Bid package means the collection of the pertinent portion of the construction documents into a…

Q: Test the accuracy of the equation by applying the operation in Ampere law (del.)? If there is a…

A: AMPERE'S LAW- It states that "Line integral of magnetic field intensity around a closed loop is…

Q: what is the receptacle load (after demand factors) for an office building with 250 receptacle…

A: Receptacle loads are described as equipment loads that are generally served by electrical…

Q: Fill in the blanks. I would love to see how to get the correct answers.

A:

Q: Q2/ 12/ why the starting O current of Y-connection less than starting current. R nt of D…

A: In this question we discuss about why the starting current in star connection is less than starting…

Q: What is the meaning of calculated load?

A: Since many different loads are connected to an electrical supply, it is extremely important to know…

Q: Briefly discuss the loaded and non-loaded telephone cables

A: Loading is the process to increase inductance of line by adding lumped inductors atpredefined…

RTD (Resistance Temperature Detector)

A resistance temperature detector is a passive electronic device or a sensor. The name itself suggests that it is related to resistance, temperature, and detection. Similarly, its resistance changes when there is a temperature change; the resistance increases when the temperature of the RTD device increases or vice-versa. It is also known as a resistance thermometer. Its working is similar to the thermocouple.