1. A force of P: = 800 N is exerted on control arm BC, which is securely attached to the solid 30 mm diameter shaft shown in the figure. Dimensions of the assembly are a = 200 mm and b = 150 mm. Determine the absolute maximum shear stress in the shaft at (a) Point H and (b) Point K. H K A P:

1. A force of P: = 800 N is exerted on control arm BC, which is securely attached to the solid 30 mm diameter shaft shown in the figure. Dimensions of the assembly are a = 200 mm and b = 150 mm. Determine the absolute maximum shear stress in the shaft at (a) Point H and (b) Point K. H K A P:

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.11.13P: A thin-walled rectangular tube has uniform thickness t and dimensions a x b to the median line of...

See similar textbooks

Related questions

Q: Find the Magnitude of the Maximum Shear Stress in the below beam and cross-section, if: w = 17 kN/m…

A: The values are w=17 kN/m, L=8 m, b=85 mm, h=78 mm

Q: The figure above shows a shaft subjected to a force P = 20 kN and a moment Mv = 600 Nm. Other data:…

A: The force applied is The moment torque is The dimension are

Q: Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 6…

Q: 3. Four pulleys are attached to the 50-mm-diameter aluminum shaft. If torques are applied to the…

Q: Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 5…

A: Diameter of tie rod (1): 5 mmDiameter of pin at B: 7 mma = 560 mm (distance between bracket A and…

Q: Determine the normal force, shear force, and moment at point C. Take that P = 8 kN and M = 33 kN . m…

Q: A solid bar having a diameter of 160 mm is to be replaced by a rectangular tube having cross-…

A: Given data: The diameter of the bar is d1=160 mm=0.16 m The cross-sectional area is A=150 mm×310…

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

1. A force of P: = 800 N is exerted on control arm BC, which is securely attached to
the solid 30 mm diameter shaft shown in the figure. Dimensions of the assembly are
a = 200 mm and b = 150 mm. Determine the absolute maximum shear stress in the
shaft at (a) Point H and (b) Point K.
H
K
A
P:

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A circular pole is subjected to linearly varying distributed force with maximum intensity t0. Calculate the diameter daof the pole if the maximum allowable shear stress for the pole is 75 M Pa.
A cylindrical tank subjected to internal pressure/? is simultaneously compressed by an axial force F = 72 kN (see figure). The cylinder has diameter d = 100 mm and wall thickness t = 4 mm. Calculate the maximum allowable internal pressure /?max based upon an allowable shear stress in the wall of the tank of 60 MPa.
A 45-mm-diameter solid steel shaft supports loads PA-1.2 KN and Pc-2.7 kN as shown. Assume that L₁ - 105 mm, L₂ = 205 mm, and 43-150 mm. The bearing at B can be idealized as a roller support, and the bearing at D can be idealized as a pin support. Determine the magnitude of (a) the maximum horizontal shear stress in the shaft. (b) the maximum tension bending stress in the shaft. L₂ C Pc Ly D
4. The solid shaft and tube shown in Figure are made of a material having an allowable shear stress of 120 MPa. Determine the maximum torque that can be applied to each cross section, and show the stress acting on a small element of material at point A of the shaft, and points 75 MPa A 100 mm B and C of the tube 75 MPa J00 mm 75 mưo 56.2 MPa 5. Show that moment of inertia for a rectangular beam (Ixx) of width b and height h is bh /12
The 40-mm diameter solid shaft ACBD is supported by two bearings at A and B. Due to the transmission of power to and from the shaft, the belts of the pulleys are subjected to the tension forces shown in the figure below. 1-Draw the moment and shear diagrams on the y z and y x planes 2-Determine the location and magnitude of the maximum bending (normal) stress. Hint draw the shaft cross section at that location and think of the associated stresses. 0.050 m 300 N 0.250 m 200 N 550 N 0.250 m 400 N 150m D 0.075 m
The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter is 75 mm and G = 35 GPa. For the steel segment BC, the diameter is 50 mm and G = 83 GPa. Given that a = 2 m and b = 1.5 m, compute the largest torque T in kN-m that can be applied as shown in the figure if the maximum shear stress is limited to 60 MPa in the bronze and 80 MPa in the steel. Answer in 2 decimal places
The mechanism below consists of a solid shaft with a diameter of 2 in between A and B and a hollow shaft with an outside diameter of 7 in and a thickness of 1/2 in between B and C. A torque T = 3 kip-in is applied as shown at A and two forces, each P = 322 lb, are applied as shown at the ends of the levers connected to Point B. Determine the shear stress that occurs on the exterior of the hollow shaft between B and C. Express answer in nearest whole psi.
A 45-mm-diameter solid steel shaft supports loads PA = 1.1 kN and Pc = 2.2 kN as shown. Assume that L₁ = 155 mm, L₂ = 330 mm, and L3 = 240 mm. The bearing at B can be idealized as a roller support, and the bearing at D can be idealized as a pin support. Determine the magnitude of (a) the maximum horizontal shear stress in the shaft. (b) the maximum tension bending stress in the shaft. A L₁ Answers: (a) Tmax= (b) max = i B L2 Pc MPa MPa L3 D
Determine the absolute shear stress for point K.
4) A 50 mm diameter solid steel shaft supports loads P₁= 1.5 KN and Pc = 3.0 KN, as shown. Assume L₁ = 150 mm, L₂=300 mm, and L3=225 mm. The bearing at B can be idealized as a roller support and the bearing at D can be idealized as a pin support. Determine the magnitude and location of (a) the maximum horizontal shear stress in the shaft and (b) the maximum tension bending stress in the shaft. P Ly B L₂ C Pc L3 D
Q / The hollow shaft has 50 mm and 40 mm outer and inner diameters respectively, and is rigid support at its ends A and B as shown in figure. If the torque (1.8 kN.m) is subjected to the shaft at point C, determine the maximum shear stress in element AC and CB as well find the angle of twist at point C. known the modulus of elasticity is 200 Gpa and Poisson's ratio is 0.3
Q1: The shaft BC is hollow with inner and outer diameters of 100 mm and 120 mm respectively. Shaft AB and CD are solid and of diameter d. For the loading shown determine the maximum and minimum shear stress in shaft BC. 0.9 m 0.7 m d 0.5 m A 120 mm T = 10 kN.m i В TB = = 20 KN.m 1 C D Tc = 30 KN.mi Tp = 6 kN - m Figure Question1