1. A downward force of 100 N is applied to the small piston with a diameter of 50 cm in the hydraulic lift system shown below. a. What is the upward force exerted by the large piston with a diameter of 2m? b. What is the mechanical advantage of this hydraulic lift? c. If the input force of 100N pushes the small piston down by 2m, how high will the large piston rise?

Q: Nizwa service station raises 6.6 kN  car of 3.4 m above the ground floor level,As shown in the below…

A:

Q: You were asked to design and manufacture a manual hydraulie device (as shown in the figure) to lift…

A: Given data:

Q: A Swimming pool 40 m long and 15 m w is 1 m and that at the deep end is 3 m. t cross-sectional areas…

A: Given: Width of the swimming pool is 15 m.

Q: Consider a cubical water tank with a side length of 3 m. The tank is half filled with water, and is…

A:

Q: In a car service station, a force of 100 N is required to raise the car on the hydraulic lift. If…

A: Given ThatF=100Nr-radius of pistonD-diameter of hydraulic Lift20D=rso10r=rm=? ****Please Note that…

Q: Two pump impellers with different diameters run at two different speeds under kinematically similar…

A:

Q: A hydraulic jack includes a master cylinder that has a piston with a diameter of 0.85 cm. The slave…

A:

Q: The following data pertains to a Hydraulic press : The diameter of the plunger and ram are 50 mm and…

A: Given:-hydralic press   plunger:-diameter(d)=5 mm=0.05 m…

Q: A 5000 N weight is pulled up on an inclined surface at a constant speed by a cylinder as shown in…

A:

Q: The ram and plunger of a hydraulic press are 150 mm and 25 mm in diameter respectively. With a…

A: Given:D=150 mm =15 cmd=25 mm =2.5 cmSp=30 cmP=1 tonnes

Q: A pump 260mm suction pipe and a 150mm discharge pipe is used to deliver 98L/s ofwater. The suction…

A: According to the given data Suction pipe diameter, ds=260 mm=0.260 m Discharge pipe diameter, dd=150…

Q: 2.) Two blocks of masses M and 3M are horizontal and frictionless is on the surface. A massless…

A:

Q: Water enters a 1-m-diameter pipe at a velocity of 5 m/s. The end of 1-m-diameter pipe reduces and…

A:

Q: When air expands adiabatically (without gaining or losing heat), it's pressure P and volume V are…

A:

Q: Two masses are fixed at 79 degrees to each other on a rotating disc, one is 3.2 kg at a radius of…

A: This question is based on the concept of balancing.

Q: C) Identify the types of water turbines and the limitations that exist within these different types?…

A: Different types of water turbine are listed below Pelton Wheel: The hydro turbine (especially an…

Q: you have a flat tire and need to pump up the tire on your car  with a hand pump, what force do you…

A:

Q: A mass of 9kg compresses a spring with spring constant 400 N/m in a vertical position for 2 meters…

A:

Q: A pump sends a substance (sg=1.9) from a tank to a tank placed at a higher level, where the velocity…

A: Given specific gravity Sg = 1.9 velocity at 2 v2 = 1 m/s friction losses  hl = 5.8 m efficiency of…

Q: Figure 4 shows the hydraulic circuit to perform work with the piston. The pump extracts oil (sg…

A: Given: Specific gravity of the oil is 0.92. The internal diameter of the cylinder is 12 cm. Length…

Q: , it is deflected upward by a curved wing with a 60° angle. The diameter is 5.08 cm and the density…

A:

Q: Two pistons of a hydraulic lift have diameters of 4 m and 2 m. What is the force exerted by the…

A: Given data: The diameter of the large piston is D = 4 m. The diameter of the small piston is d = 2…

Q: A firehose rodeo contestant is riding a hose that sprays water vertically downward from a 1 inch…

A: Givend=1inch=0.0833 ftD=5inchW=155 lbfρw=1.94 slug/f3=1.94×32.174=62.417 lb/ft3

Q: Q.1) for the system shown in figure (a). The pump has the characteristics shown in figure (b). What…

A: Pressure in the lower tank, PL=35 lb/in2=35*144=5040 lb/ft2Pressure in the upper tank, PU=10…

Q: After a particularly intense test in Engineering, Toby sits down to enjoy a nice cool very large…

A:

Q: Determine the pump head (unit: meter or kPa), using the following parameters

A:

Q: A pump delivers water (density equals 1000 kg/m^3) at a steady rate of 1219 L/min as shown in the…

A: The steady flow energy equation is the equation of the first law of the thermodynamics for an open…

Q: Concept more important than solution here! Nozzles -Water jets What is the pressure at nozzle 1?…

A: Given:Depth of nozzle 1, h1=30 cm=0.3 mDepth of nozzle 2, h2=60 cm=0.6 mDepth of nozle 3, h3=90…

Q: If the piston mass is 20 kg and the car mass with its base is 400 kg, what will the minimum pressure…

A: we need to calculate minimum pressure required to lift the car

Q: Fluid flows through the pipe into a rigid tank in the shape of a cube. During that process, heat is…

A: Let's assume The initial mass in the constant volume cube is mCv1 The entering mass in the constant…

Q: A jet of freshwater strikes a series of vanes of a turbine at 25° with the direction of motion and…

A: Note: As per our guidelines we are supposed to answer only the first 3 sub-parts. Kindly repost…

Q: In a hydraulic system The volume of oil displaced by a cylindrical effort piston with 20 cm diameter…

A: We have to find the stroke length of this piston cylinder .

Q: A train has a weight of 100 tons (2,000lbf) is stopped from 4 mph in 1 ft by a hydraulic cushion.If…

A:

Q: Water flows over a waterfall 328 Ft in height. Take 2.204 lb of the water as the syste and assume…

A:

Q: An open container made of metal is placed ona scale. Water flows into the container through an…

A: