1. A cylinder with a mass 0,20 kg is sliding downwards through a vertically positioned pipe. A thin oil layer exists between the cylinder and the pipe's internal surface. Centerline of the cylinder and the pipe overlap. (Yon =8044.2 N /m? ; vol=6-10° m²/s). Find the change in the speed of cylinder in the pipe with respect to its unit displacement and the shear stress that acts upon the oil layer. A A L= 150 mm 73.8 mm 74 mm 0.1 mm

Q: Determine the distance from the upper surface of the symmetric double-T beam cross section to the…

A: Given:- To find:- Distance H from the upper surface Concept:- Location of centroid of the section…

Q: Solve for the end moments consider sidesway 60KN 10KN/m 2m 2m B A 1.51 1.51 5m 21 21 21 4m 4m

A:

Q: Q2/ Determine the resultant moment of the forces about point I F=400N 100 N D 30 A B C 45°

A:

Q: w = N/m Omax 764EI at x = 0.475L

A: This is fixed beam with uniformly varying load and find out deflection at x = 0.475L.

Q: Problem 4 - Two homogeneous rods ABCD and BE are bent as shown and rigidly connected to each other…

A: Two homogeneous Rods are given as shown in the image above and it has been asked in the question to…

Q: nswer all the questions

A:

Q: Five forces are acting on the cantilever beam AB. Find the resultant or a couple acting on the…

A:

Q: Water Flow into horizontal pipe with velocity of v. Determine the horizontal and vertical component…

A: We will take value of v1 = 3 m /s D1 = 0.6 m D2 = 1.5 m

Q: 1.) Determine the resultant of the forces acting on the body. 450KN 600KN 2 1 4 200kN 15 12 2 250kN…

A:

Q: Determine the moment about point O in terms of N-m. – 4 ft- 3 ft 45°. |-1 ft-| 50 N

A: The FBD of the section is shown below:

Q: The continuous beam is loaded as shown below. a. b. C. determine the moment at point 1 (M₁)…

A:

Q: Problem 6: Replace the force of F = 80 N acting on the pipe assembly by an equivalent resultant…

A: Equivalent resultant :∑ F=RR=80×cos30×sin40i+80×cos30×cos40j-80sin30kR=(44.53)i+(53.07)j-40kPosition…

Q: (0.80) D The 5 ft diameter cylinder weighs 5000 lbs. and is 5 ft long as shown. Determine the…

A:

Q: 30 034 L500.7L

A:

Q: Provide illustration and label accordingly The uniform slender rod AB shown of weight W is…

A: The given data is shown below: θ=30°f=0.3

Q: Derive the equation for the maximum moment of the beams shown. write your answers here. a) W B L/2…

A: To find maximum moment,we will find reactions at supports,Then using reactions we will draw shear…

Q: The continuous beam is loaded as shown below. a. b. C. determine the moment at point 1 (M₁)…

A: Solution:   RA+RB=703×2+70-703×12×3=116.67 kN ∑MB=0 RA×2-703×2-70-703×12×3×23=0RA=46.67…

Q: 1) Draw the shear and moment diagrams for the given frame. It is fixed at point B. Write the shear…

A:

Q: What is the moment at C to the nearest 1 k-ft? Be sure to use the correct sign. L1 = 6 ft L2 = 5…

A:

Q: Determine the spin and arrow equations for the next beam. If any constant is worth zero you must…

A:

Q: The continuous beam is loaded as shown below. a. b. C. determine the moment at point 1 (M₁)…

A:

Q: Problem 3 Five forces are acting on the cantilever beam AB. Find the resultant or a couple acting on…

A:

Q: The trailer has a mass of 400kg and the mass center at G. is being pulled by a horizontal force of…

A: Newton's second law of motion: Newton's second law of motion describes the motion of the body.…

Q: 3 30 300 Ib 722 Ib

A: Compute the resultant of the three forces shown. Locate its intersection with the X and Y axes

Q: The continuous beam is loaded as shown below. a. b. C. determine the moment at point 1 (M₁)…

A:

Q: The continuous beam is loaded as shown below. a. b. C. determine the moment at point 1 (M₁)…

A:

Q: 15KN 15kN 4 30° 45° 30 PA 25KN F.

A:

Q: Base from the path of the projectile as shown in the figure. What must be the 6, in order for the…

A: v= 70ft/s l= 150 ft to find  angle of throwing missile

Q: Compute the midspan value of El y for the beam loaded as shown. 300 N/m A B |.5m 05 2 m

A: Given data:

Q: Determine the internal normal force, shear force, and moment at point D in the beam. Ans: AD = -1350…

A: Step 1: Step 2: Step 3: Step 4:

Q: Determine the resultant of the load acting on the beam ABC and the location of the resultant from…

A: load = Area  of the figure ..   For UDL = resulting force is halfway  For UVL = 2l/3 from free end…

Q: The continuous beam is loaded as shown below. a. b. C. determine the moment at point 1 (M₁)…

A:

Q: D. In the figure, the coefficient friction of Block A and B are 0.15 and 0.25 respectively. Block C…

A: We have to determine the value of tensions at Pulley connecting A and B, b and c, Force at A and B…

Q: The 10 kg block is pressed against the spring so as to compress it 2 m when it is at A. If the plane…

A:

Q: The 609-N force is applied to the 112-kg block, which is stationary before the force is applied.…

A:

Design criteria for structural loading

The different loads such as loads due to self-weight (dead load) and external loads such as live load, wind loads, seismic load, snow load, and other loads and load combinations that influence the design of a building are called structural loading. The nature of the applied load differs from changes in the location, design, and type of materials used. The design criteria require that structures must be designed and constructed to be able to withstand all load types that are expected to act upon the structure and render its usage for the designated purpose. The structural members such as beams, slabs, columns, and foundations help the structure to withstand the applied load. There are different institutes such as ASCE and ACI that provide building design codes to assure minimum safety requirements and quality of the structures.