1. a bow uses a 16-gram arrow as its ammo, and its string behaves as an ideal spring. When the string is fulled back at 85cm, a force of 200 N is needed. Find the maximum height of the dovrow if shot upward if using this length. Neglect air resistance as the arrow travels.

1. a bow uses a 16-gram arrow as its ammo, and its string behaves as an ideal spring. When the string is fulled back at 85cm, a force of 200 N is needed. Find the maximum height of the dovrow if shot upward if using this length. Neglect air resistance as the arrow travels.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The figure on the left, below, shows a non-uniform bent rod with a mass of 5 kg. Your job is to determine the location of the center of gravity of this rod. You design an experiment: you connect a pin and cable to the rod such that it safely stays in static equilibrium under a force P that you apply. Then, you apply forces between 0-100 N, and measure the tension force on the cable using a cable tension meter. The results of your experiment are shown in the figure, on the right. Using this experiment, calculate (approximately) the horizontal distance (x in the figure) between point A and the center of gravity G of the bent rod. B C O I 20 cm 20 cm 60° D 50 cm Tension measurement [N] 60 50 40 30 20 -10 0 10 real data estimated fit 20 30 40 ܐܐܝ 50 P[N] 60 70 80 90 100
11. height of 4.5 feet. How much will the spring be compressed? If a spring has a force constant of 250 N/m and a 175g block is dropped onto the spring from a
2. The 6-kg frame AC and 4-kg uniform slender bar AB of length / is free to slide along a smooth fixed horizontal rod. a. Find the tension in the wire BC for a static case where the frame and bar are stationary. b. Now, with the the 80 N force applied find the tension in the wire BC. 60° to Q B 60° -80 N -x
A vertical spring with a mass attached at its end stretches by an amount 20 cm before coming to rest. The same spring and mass is now placed on a smooth inclined plane with one end fixed to the top of the plane. The plane makes an angle of 30° with the horizontal. By how much will the spring stretch before coming to rest? |The spring on the inclined plane is stretched further by 15 cm and released from rest. What is its speed when it passes through the new equilibrium position?
2. For the system below: a. Give an equation of motion for h. Note that the system has two inputs, p1 and p2. b. When h= 5, give the force exerted on the bottom of the tank. (Assume that the width and height of the opening at the bottom of the tank is negligible. The area of the bottom of the tank is A). h PA PI P2 PA R
Two box hang from the ends of a string suspended from a frictionless pulley. The mass on the left is chosen to create a tension of 4 N in the string. The box on the right has a weight of 2 N. What will be the acceleration of the box on the right? Assume the acceleration of gravity is 9.8 m/s?. 4 N 2 N
5. A 25.0-g mass is attached to a vertical spring and it stretches 15.0 cm. It is then stretched an additional 10.0 cm and then released. What is the maximum velocity of the mass? What is its maximum acceleration? Vmax = Dmax =
Blocks mị and m2 are connected by a rope as shown in the figure. There is friction between mi and the wall, where the coefficient of static friction is ls. There is no friction between m2 and the ramp. An unknown force P is applied to mį so that mị is about to slip down the wall and m2 is about to move down the ramp. If the magnitude of the normal force on m2 is n2, find m2, the magnitude of P, the magnitude of the friction force on m1, and the magnitude of the tension force in the rope. The knowns are ls, n2, m1, g, and 0. P = ? Hs rope wall no friction m2 = ? ramp
3.2 Sliding blocks with friction* Mass MA = 4kg rests on top of mass Mg = 5 kg that rests on a fric- tionless table. The coefficient of friction between the two blocks is such that the blocks just start to slip when the horizontal force F applied to the lower block is 27 N. Suppose that now a horizontal force is applied to the upper block. What is its maximum value for the blocks to slide without slipping relative to each other?
At max load, the elevator E weighs 8000 lb. The counterweight C weighs 3500 lb. Research shows that generally speaking, elevator speeds reach up to 600 ft/min, and are designed to accelerate at about 10 ft/s². If the elevator is at capacity, the motor has an efficiency of 85%, and the mechanical systems (pulleys, cables, etc.) experience various energy losses totaling 30%, find the required power input to the motor if... (a) The elevator is accelerating and moving up at maximum rates. (b) The elevator is moving up at a constant max rate. (c) The elevator is moving down at a constant max rate. E C M
1. A uniform stick can be balanced on a knife edge 10 cm from one end when a load of 200 N is hung from that end. When the knife edge is moved 5 cm further from the end, the 200 N load has to be moved to a point 8.75 cm from the knife edge to obtain a balance. Find the length of the stick and its weight.
The handle of a small hand pump is 850mm long. The fulcrum is attached at one end and the load plunger is located 50 mm from the fulcrum. An effort of 600N is applied downward at the opposite end from the fulcrum. Find the force exerted by the load plunger and the mechanical advantage of the lever.