1. A 65 wt% Ni -35 wt% Cu alloy is heated to a temperature within the a + liquid phaseregion. If the composition of the a phase is 70 wt % Ni, determinei.The temperature of the alloyii.The composition of the liquid phaseiii.The mass fraction of both phasesComposition (at% Ni)204060801001600H 28001500Liquid1453°C26001400Solidus lineLiquidus line24001300a +L120022001100A20001085°C100020406080100(Cu)Composition (wt% Ni)(Ni)Temperature (°C)Temperature (F)

To Determine,The temprature of the alloyComposition of the liquid phase Mass friction of both phases

1. A 65 wt% Ni -35 wt% Cu alloy is heated to a temperature within the a + liquid phase region. If the composition of the a phase is 70 wt % Ni,determine The temperature of the alloy ii. The composition of the liquid phase The mass fraction of both phases i. ii. Composition (at% Ni) 20 40 60 80 100 1600 2800

1. A 65 wt% Ni -35 wt% Cu alloy is heated to a temperature within the a + liquid phase region. If the composition of the a phase is 70 wt % Ni,determine The temperature of the alloy ii. The composition of the liquid phase The mass fraction of both phases i. ii. Composition (at% Ni) 20 40 60 80 100 1600 2800

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Make a comparison between polymers and ceramics based on (a) mechanical properties and (b) on molecular structures under the effect of heating to temperatures.
A sufficient amount of pure copper is(4 to be heated for casting a large plate in an open mold. The plate has dimensions: length = 20 in, width=D10 in, and thickness =3 in. Compute the amount of heat that must be added to the metal to heat it to a temperature of 21500F for pouring. Assume that the amount of metal heated will be 10% more than what is needed to fill the mold cavity. Properties of the metal are: density=0.324 Ibm/in3, melting point = 19810F, specific heat of the %3D metal=0.093Btu/lbm-F in the solid state and 0.090 Btu/lbm-F in the liquid * .state, and heat of fusion = 80 Btu/lbm
(b) Demonstrate that the following equation is dimensionally homogenous. [10 %] Ixc Yp = ye+ Ayc fluid mechanics
42)
Describe the Assembly of atoms forming the basic clay mineral sheet alumina octahedron .
Define a ceramic material and state the 5 properties that iscommon to ceramic material.
All the following statements are true for ceramics except __________________. Question 26 options: Electrical conductivity of ceramics is generally lower than metals. Most ceramics are lighter than metals but heavier than polymers. The melting point of ceramics is lower than most metals. Thermal expansion of ceramics are less than for metals.
A 100.0-mL sample of spring water was treated to convert any iron present to Fe+2. Addition of 25.00-mL of 0.015102 N K2Cr2O7 resulted in the reaction. The excess K2Cr2O7 (294 g/mol) was back-titrated with 8.53 mL of 0.00949 N Fe+2 solution. The concentration of Fe+2 (56 g/mol) in the sample in parts per million is ___________.
steel A aluminum 2 m B 2 m 9 m bronze с 3 m The assembly shown consists of a steel cylinder (E = 200 GPa, A = 150 mm2,= 12 µm/m-°C), an aluminum alloy cylinder (E = 70 GPa, A = 230 mm2, = 23 µm/m °C), and a hollow bronze tube (E = 100 GPa, A = 190 mm2, = 18 μm/m-°C) welded to the rigid bar at points A, B, and C, respectively. Initially, the system is stress-free. When the assembly is heated by 45°C, determine the normal stress (in MPa) in the bronze tube and the horizontal distance (in m) with reference to point A where the rigid bar tilts. Neglect the weight of the members. The answer should be: Obr = 8.9507 MPa, C, d = 4.6625 m
This is a physiochemaical property of engineering materials that exhibits its ability to change its volume due to moisture change
35 Material Science and Engineering
At a temperature of 60°F, a 0.04-in. gap exists between the ends of the two bars shown. Bar (1) is an aluminum alloy [E = 10,000 ksi; v = 0.32; a = 12.5 x 10-6/°F] bar with a width of 3.0 in. and a thickness of 0.75 in. Bar (2) is a stainless steel [E = 28,000 ksi; v = 0.12; a = 9.6 x 10-6/°F] bar with a width of 2.0 in. and a thickness of 0.75 in. The supports at A and C are rigid. Determine (a) the lowest temperature at which the two bars contact each other. (b) the normal stress in the two bars at a temperature of 250°F. (c) the normal strain in the two bars at 250°F. (d) the change in width of the aluminum bar at a temperature of 250°F. (1) 3.0 in. 32 in. 2.0 in. B ↓ (2) 44 in. 0.04-in. gap Determine the lowest temperature, Tcontact, at which the two bars contact each other.