1. A 50-hp, 250-V 1200 r/min dc shunt motor with compensatingwindings has an armature resistance (including the brushes,compensating windings, and interpoles) of 0.06 2. Its field circuithas a total resistance Radj + Rr of 50 22, which produces a no-loadspeed of 1200 r/min. There are 1200 turns per pole on the shuntfield winding (see figure). Find the speed of this motor when itsinput current isA. 100 A.B. 200 A.C. 300A.IEARAwww0.06 Ω50 ΩRadj12RFLFIL|¹FNF =1200 turnsVT = 250 V

In this question we need to find the speed of the given motor at following values of input current…

1. A 50-hp, 250-V 1200 r/min dc shunt motor with compensating windings has an armature resistance (including the brushes, compensating windings, and interpoles) of 0.06 2. Its field circuit has a total resistance Radj + Rr of 50 2, which produces a no-load speed of 1200 r/min. There are 1200 turns per pole on the shunt field winding (see figure). Find the speed of this motor when its input current is A. 100 A. B. 200 A. C. 300A. I EA RA 0.06 Ω 50 Ω Radj RF LF IL IF NE= 1200 turns VT = 250 V

1. A 50-hp, 250-V 1200 r/min dc shunt motor with compensating windings has an armature resistance (including the brushes, compensating windings, and interpoles) of 0.06 2. Its field circuit has a total resistance Radj + Rr of 50 2, which produces a no-load speed of 1200 r/min. There are 1200 turns per pole on the shunt field winding (see figure). Find the speed of this motor when its input current is A. 100 A. B. 200 A. C. 300A. I EA RA 0.06 Ω 50 Ω Radj RF LF IL IF NE= 1200 turns VT = 250 V

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 3-phase, 50-Hz induction motor with its rotor star-connected gives 500-V(r.m.s.) at standstill between the slip-rings on open-circuit. Calculate the current and power factor at standstill when the rotor winding is joined to a star-connected external circuit, each phase of which has a resistance of 10 Q and an inductance of 0.04 H. The resistance per phase of the winding is 0.2 Q and its inductance is 0.04 H. Also, calculate the current and power factor when the slip-rings are short-circuited and the motor is running with a slip of 5 per cent. Assume flux remain constant.
Q2. A 230 V single-phase induction motor, 50 Hz, has the following winding impedances (at rest): Zm=28 <70° Q. Za=42 <45°Q A) Calculate the input current at start-up. B) Obtain the amount of capacitor in series with the auxiliary winding for which the torque Maximum startup. Then compare the input current, auxiliary winding current and torque all at start-up in two modes with and without starter capacitor.
what are the disadvantages of slip ring induction motor?
What is the relationship between slip s) and load (Pa) in an induction motor? Please explain.
The armature resistance of a shunt motor fed from a 220 Volt DC source is 5 ohms and the resistance of the excitation winding is R ohm and it rotates stably. Then, a resistance of R ohm is added to the excitation circuit (a resistor with the same value as the winding resistance) to control the speed. How many RPM is the motor in the last state in steady state.Mechanical losses will be neglected, motor magnetically linear, no saturation, temperature change will be neglected.Armature current = Ia = 4 ALoad torque=Tload= 7 Nm
A three-phase, 460 V, 98hp 1,60 Hz, four-pole induction machine delivers rated output power at a slip of 0.05. Determine: (i) The synchonous speed. (V) speed at half Load (ii) The motor speed. (iii) The rotor frequency. (iv) The slip speed. ...A... -
Reducing the supply voltage so that Vnew = Vold / V3 reduces the maximum torque of the motor so that Tmaxnew= ...Tmaxold . * .... ...
Q5) discuss two only : a) the frequeney of an alternator. b)what is the disadvantages of split phase induction motor. c) discuss the armature and shunt torque of the DC motor.
pole. 50-Hz. 3-ϕ induction motor has a full-load speed of 950 rpm. At half load its speed would be ..... rpm a) 475 b) 500 c) 975 d)1000
3. A 440V 60-hp six pole 60 hz A connected induction motor has the following parameters R1=0.048 R2= 0.035 Xm= 9.50 X1= 0.33 0 X2= 0.37 0 Pcore= 600W PF&W= 350W Use the Thevenin's Equivalent circuit concept to find: (a)Vth and Zth seen by the rotor circuit (b)The slip at which maximum torque occurs (c) the value of Max/pullout Torques (d) The starting torque.
Choose True (V) or false( x) for the following : 4) Reluctance is a measure of "opposition" the magnetic circuit offers to the flux. 5) The rated output power (transformer rating) can be used to determine the turns ratio of the transformer. 6) With the increase in speed of a series DC motor, Both back emf as well as line current increase. 7) When an induction motor is stationary, the stator and rotor windings form the equivalent of a transformer. 8) Increasing the load current for DC Self-excited generator Shunt-Wound Generator will increase the terminal voltage. 9) In lap windings there are as many paths in parallel and used to produce high current, low voltage output. 10) In 3-pahse induction motor, if the rotor speed increases, the rate at which the rotating magnetic field cuts the rotor bars is increasing.
A 3 phase, 1500 rpm, 2200 V, star connected synchronous motor has an impedance of 0.4+j90 per phase. At some excitation 2900 V is induced in the armature. Find the maximum torque developed by motor before the motor breaks out of synchronism. Also find the load angle this time.