1- Write a program in assembly language for the 8085 microprocessor to send 10 bytes of data located at the memory address (3000h) using SOD at a baud rate of 1200. Information: The 8085 processor operates at a frequency of 3.072 MHz. And two high pulses must be sent before each byte (start bits) and one low pulse after each byte (end bits). You can use this flowchart, but you should notice that this flowchart deals with one byte, and you are required to deal with 10 bytes Transmit

1- Write a program in assembly language for the 8085 microprocessor to send 10 bytes of data located at the memory address (3000h) using SOD at a baud rate of 1200. Information: The 8085 processor operates at a frequency of 3.072 MHz. And two high pulses must be sent before each byte (start bits) and one low pulse after each byte (end bits). You can use this flowchart, but you should notice that this flowchart deals with one byte, and you are required to deal with 10 bytes Transmit

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Write an assembly program that: 1. Sets the cursor position at the 5th row & 10th column. 2. Displays 'O' at the cursor position. 3. Waits for user entry of one character. 4. User can enter any of the five characters: (a) 'q': the program quit. (b) 'w': moves the character one row up. (c) 'z': moves the character one row down. (d) 'a': moves the character one column left. (e) 'd': moves the character one column right. 5. When the character ('O') reaches the edge it should complete from the opposite side in the same row/column (just like the simple snake game). << YOUR CODE SHOULD WORK CORRECTLY VIA TASM >> * Any two identical programs will be evaluated to zero !!! Submission: **.asm code and a screenshot for the output screen !! Output screenshots
Write an assembly program that: 1. Sets the cursor position at the 5th row & 10th column. 2. Displays 'O' at the cursor position. 3. Waits for user entry of one character. 4. User can enter any of the five characters: (a) 'q': the program quit. (b) 'w': moves the character one row up. (c) 'z': moves the character one row down. (d) 'a': moves the character one column left. (e) 'd': moves the character one column right. 5. When the character ('O') reaches the edge it should complete from the opposite side in the same row/column (just like the simple snake game). << YOUR CODE SHOULD WORK CORRECTLY VIA TASM >> * Any two identical programs will be evaluated to zero !!! Submission: **.asm code and a screenshot for the output screen !! Output screenshots Ou
Computer Science Implement the following expression in assembly language: EAX = (valDW1+valDW2) −EBX. Assume that valDW1 and valDW2 are 32-bit integer variables.
Use emu8086 –assembler and microprocesser emulator 4.08 language to: Write a program to read a letter in lower case the convert this letter to upper case and print it. (to convert from lower to upper subtract from the value 20h)
You have studied Rotate Instruction of 8086 microprocessor in Computer Organization & Assembly Language Programming course. The Instructions were (ROL, ROR, RCL and RCR). Design a circuit that is given a 3 – bit number as input. The circuit rotates the input number 2 times to right (ROR instruction). HELP ( Just calm down. Forget ROL, RCL and RCR instructions. Just recall the logic of ROR instruction. Be very careful in drawing the truth table. Rest is easy.
i. Using a flow graphic and an Intel microprocessor, briefly describe how adding two binary integers works. ii. For the flowchart above, create a pseudocode and a code in any easy assembly language. iii. To perform a reduction procedure, follow steps I and ii above.
2- Write an assembly program by emu8086 to display the largest of three variables. The three variables num1, num2 and num3 have values 89,20 and 56, respectively.
5. When designing register file, we used multiplexer to read from a specific register of that register file. However, to write in the register file, we didn’t use demultiplexer. Why ? 6. In our designed register file, we can write one data at a time. But if we want to write two data at a time,what should we do ?
5. Write a program to evaluate the arithmetic statement: X= (A*[B+C*(D+E)])/(F*(G+H)) i. Using a general register computer with three address instruction ii. Using a general register computer with two address instruction iii. Using a accumulator type computer with one address instruction
write Assembly code that processes an text input, each number (between 0 and 9) should be converted to letters. For example: 5 -> five
MIPS Assembly Write a program for RISC MIPS 32bits that challenges a person to guess a number of up to 3 digits before and 3 digits after the comma, that is, a value between 000,000 and 999,999. The program user will try to guess the number with multiple attempts, where the program will indicate at each attempt if the informed number is bigger, smaller, or if the user guessed correctly. When this happens, the program ends, showing a SUCCESS message and a total count of the number of attempts taken to get it right. The program must have a SUBROUTINE as described below. SUBROUTINE:- Input Parameters: user guess, expected value- Output: message on screen (bigger, smaller, SUCCESS)- Returns: value 1 if correct, 0 if incorrect