B- Choose correct answer1- What is the output of the following codeвх-23763, С1.- 8ROL BX,CLa. BX-SCD3, CF =0 b. BX-D35C, CF= 0c. Bx-689D, CF= 1 d. BX-D98C, CF- 12- Shift instruction area. data manipulation instructionsb. data transfer instructionsc. program control instructiond. all of the above3- Instructions that affect data in memorya. INc. MOVb. OUTd. All of the above4- In direct I/O transfers can take place between I/O port anda. ALb. BLc. CLd. DL5- 1/0 instructions, 16-bit address must be inа. АХb. ВХc. DXd. All of the above

We are authorized to answer one question at a time, since you have not mentioned which question you…

Answered: 1- What is the output of the following…

1- What is the output of the following code BX= 23763, CL.= 8 ROL BX,CL a. BX-5CD3 , CF=0 b. BX=D35C,CF= 0c. BX-689D, CF= 1d. BX=D98C, CF- 1

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

I need the answer as soon as possible
Answer the question Electronic
. For the circuit shown in figure. Vcc For the circuit shown in Figure If Ve=1ov, B200, 2.5k2 RI - 1ov If =201 A Iksz
In order to connect a LED to one of the pins: O You need to define that LED as an OUTPUT in the setup function O You need to define that LED as an OUTPUT in the loop function You need to define that LED as an INPUT in the setup function In order to control a DC motor from a computer: We need a DAC such that data will flow from computer to DAC and from DAC to DC motor We need an ADC such that data will flow from computer to ADC and a DAC so data flows from DC motor to computer We need an ADC such that data will flow from computer to ADC and from ADC to DC motor In order to light a LED: O send a HIGH signal and this will be written in the setup function send a LOW signal and this will be written in the Loop function send a HIGH signal and this will be written in the Loop function If you want an LED to blink: O You can connect it directly to one of the digital pins of the Arduino O You need a digital to analog converter between the Arduino and the LED O You can connect it directly to one…
Design Problem: Design a clamper circuit based on the input and output waveforms shown in the diagram below: Design Voltage Input Voltage Output Assign peak value of your Voltage Input and frequency. Solve theoretically
In order to connect a LED to one of the pins: O You need to define that LED as an OUTPUT in the setup function O You need to define that LED as an OUTPUT in the loop function You need to define that LED as an INPUT in the setup function In order to control a DC motor from a computer: We need a DAC such that data will flow from computer to DAC and from DAC to DC motor We need an ADC such that data will flow from computer to ADC and a DAC so data flows from DC motor to computer We need an ADC such that data will flow from computer to ADC and from ADC to DC motor In order to light a LED: O send a HIGH signal and this will be written in the setup function send a LOW signal and this will be written in the Loop function send a HIGH signal and this will be written in the Loop function If you want an LED to blink: O You can connect it directly to one of the digital pins of the Arduino O You need a digital to analog converter between the Arduino and the LED O You can connect it directly to one…
In order to connect a LED to one of the pins: O You need to define that LED as an OUTPUT in the setup function O You need to define that LED as an OUTPUT in the loop function You need to define that LED as an INPUT in the setup function In order to control a DC motor from a computer: We need a DAC such that data will flow from computer to DAC and from DAC to DC motor We need an ADC such that data will flow from computer to ADC and a DAC so data flows from DC motor to computer We need an ADC such that data will flow from computer to ADC and from ADC to DC motor In order to light a LED: O send a HIGH signal and this will be written in the setup function send a LOW signal and this will be written in the Loop function send a HIGH signal and this will be written in the Loop function If you want an LED to blink: O You can connect it directly to one of the digital pins of the Arduino O You need a digital to analog converter between the Arduino and the LED O You can connect it directly to one…
build an inverting summing amplifier with 2 inputs: a 1 V DC signal anda sine wave with an amplitude of 2 V and 1 kHz frequency.V Simulate for 2 msec
i need the answer quickly
Draw the output on top of the input waveforms for the circuits below. For all circuits in this question, assume that +Vout(max)= +10V and -Vout(max)= -10V .
Sketch the output voltage waveform for each op armp circuits given below. Given the maximum outputvoltage for the op-armp is Vomax = +10 v and Vomin = -10 v.Use input voltage for all circuit as shown. Also use V2 = 4.7 V for D1 and D2. V. 0 -5V- -5V D1 Kt 1K 1K D2 V1 V2
Digital e