(1) Ulsing suitable illustrations, design an ammeter with current ranges 20mA, 0.5mA and 100μ A using an instrument that has f.s.d. at 50μA and a resistance 500 of

Q: What are the types of Multiplexers?

A: To explain: Types of Multiplexers

Q: What are rectification technologies

A: The rectifier technology is employed to convert AC voltage supply into DC voltage supply. Based on…

Q: Choose the correct statement below motors are actuators but not transducers DC motors and servo…

A: The actuator generates motion in the system by changing the electrical energy into mechanical. The…

Q: Why is electronics important?

A: Electronic devices have become an indispensable part of our daily lives. It is becoming increasingly…

Q: Modulator is a term used to describe any device that converts signals.explain

A: For the wireless transmission of the signal, the signal message signal must be amplified and must be…

Q: 6 What is the relay and what are its two circuits?

A: to know about the relay.

Q: 22. a) Describe how the following sensors are used to measure temperature. i) RTD

A: Any system can be autonomous or manual. A system is called autonomous if the output is independent…

Q: A 1-p On-Off AC voltage controller has the supply voltages of 220 volts and rms output voltage is…

A: In a single phase ac ON OFF voltage regulator  Input voltage 220V Output voltage = 110 Find the duty…

Q: A speedometer is connected in an automobile system to measure the speed. The meter reads 120.8 rpm…

A: In this question we need to choose a correct option

Q: write a short note on balance modulator.

A: Introduction A balanced modulator is a circuit that produces double-sideband suppressed-carrier…

Q: Q3 An AC bridge is shown in Figure Q3. It has an AC excitation input and four arms of impedances,…

A:

Q: Q1/ What are the difference between bridge uncontrolled rectifier and bridge-controlled rectifier

A: Difference between controlled rectifier and uncontrolled rectifier is given in below table Sl.No…

Q: explain about mechanical test in routin test of C B

A: Testing of a circuit breaker are of two types:  Type Tests  Routine Test. The circuit breakers carry…

Q: when using lm393, is it necessary to use a pull up resistor between the output and the power supply?

A: It is asked to discuss why we need to use a pull up resistor between the output and the power…

Q: What's the peak time for this system with its closed-loop poles as shown? jo Select one: O a. 1.57…

A: From figure, jwd=j2 wd=2 rad/s

Q: What does balance modulator generate and what does it eliminate.

A:

Q: Compare between servo motor and universal motor

A: Solution Servo motor does not rotate freely and continuously like DC motor. Its rotation is limited…

Q: With suitable sketch ,explain in detail the calibration procedure of differential pressure…

A: Differential Pressure Transmitter- Differential pressure transmitter is a device which is used…

Q: what are charging and discharging time of this circuit.

A: Given circuit is -

Q: discribe the key step in the design a Contral System

A: There are basically 4 step to design a desirable control system. The block diagram of the control…

Q: A type of noise that is directly proportional to the frequency of the operation. a. shot noise b.…

A: Another quite noise that happens in transistors is referred to as transit time noise. Transit time…

Q: What is the modus operandi motion control lamp Please not handwriting

A: the modus operandi motion control lamp

Q: 1. What is lightning? Describe the mechanism of the lightning discharge.

A: According to guidelines we need to solve only the first question. we have to explain lightning and…

Q: What is digital demodulator

A:

Q: In an On Off AC voltage controller, one of the given statement is false The duty cycle is always…

A: For the ON off ac voltage regulator  Which Statment is wrong

Q: What is offset voltage?

A: Offset voltage, also known as input offset voltage or simply Vos, is a parameter commonly associated…

Q: Using a digital multimeter, what are the indicators if a diode is defective and is considered…

A:

Q: Interpret what is in the figure

A: Control systems are represented by transfer function. This  can be written in both time domain and…

Q: Identify the part of measurement system which can convert change in resistance to change in current…

A:

Q: he Dc and Ac power of the rectifier circuit are 367watts and 276 watt respectively, the efficiency…

A: RECTIFIER/CONVERTER EFFICIENCY: The converter efficiency is nothing but the ratio of D.C output…

Q: Create a block diagram or a circuit of a gyroscope

A: It is asked to create a block diagram of a gyroscope.

Q: 2. Explain the principle of operation for the following meters a. Moving Iron meter b.…

A: Moving Iron meter is used to measure the applied unknown voltage or current An electrodynamic…

Power Measurement

According to Blondel's theorem, the total power is measured with one less number of wattmeters than the number of wires present in the system. So, a single-phase and two-wire system will require one wattmeter and a single-phase and the three-wire system will require two wattmeters, and a three-phase and the three-wire system will also require two wattmeters and a three-phase and the four-wire system will require three wattmeter devices. The wattmeter is a device that measures power using one voltage and one current input as shown in the above figure. Multiple current or voltage input pair cables are used by many power analyzers and digital storage oscilloscopes (DSOs) for measuring watts, in effect within a single instrument acting as multiple wattmeters. It is possible to measure three-phase and four-wire power with one correctly specified power analyzer.