1) The 15-kg block A and 25-kg cylinder B are connected by the light cord that passes over a 5-kg pulley with IG = 0.025 kg.m2. If the system is released from rest, (with coefficient of friction between the block and ground of 0.3) calculate the angular acceleration of the pulley

Q: When a force of P = 31 lb is applied to the brake arm, the 48 lb cylinder A is descending with a…

A:

Q: Question 17 The 3-kg disk Dis attached to the end of a cord. The other end is attached to ball and…

A: We have given

Q: The uniform 15-kg bar is supported on the horizontal surface at A by a small roller of negligible…

A:

Q: A motor winds in a cable with a constant acceleration such that a 77-kg crate, which is initially at…

A:

Q: Problem 1: The 1.2-kg uniform slender bar rotates freely about a horizontal axis through O. The…

A: Given data: Mass of slender bar, m=1.2 kg. It's length is 0.8 m It freely rotates about fixed end…

Q: The coefficient of kinetic friction under block A in Fig. 24-A is 0.30 and under block B is 0.20.…

A:

Q: 2. A car and its load weighs 40 kN and the center of gravity is 600 mm from the ground and midway…

A:

Q: The 186-lb exerciser is beginning to execute a bicep curl. When in the position shown with his right…

A: Given data WE=186 lb WC=22 lb ay=0.30g

Q: b) What will happen if the maximum mass of body B resulted in part (a) is doubled? In Question (3):…

A:

Q: What normal force is exerted on the refrigerator by the floor at A? Express your answer with the…

A:

Q: Two blocks are joined by an inextensible cable as shown in the figure. Coefficient of kinetic…

A:

Q: B 20° 30Р

A: Calculate acceleration of Bmass of block A mass of block B and the angles

Q: In the diagram below, a force P of 750 N is applied to the 350 kg block. Find the acceleration of…

A:

Q: Carl presses a small toy of mass m to the right agaist a spring of force constant k until the spring…

A: Given data: Radus=R Need to determine the normal force at point A and minimum compression in spring.

Q: calculate the value of the static friction force acting on the disk D at the instant it starts its…

A:

Q: To set up and solve the equations of motion using rectangular coordinates The 3.5 -kg collar shown…

A: (b) Consider the free body diagram shown below for the given condition.

Q: If the given system is released from rest in the position shown, calculate the velocity of B when it…

A:

Q: Q4: The uniform 4 m boom has a mass of 60 kg and is pivoted to the back of a truck at A and secured…

A: Find the total force supported by the conection at A.

Q: The blocks are joined by an inextensible cable as shown. If the system is released from rest, what…

A:

Q: A car of mass 700 kg travels round a horizontal curve of 60 m radius. The centre of gravity of the…

A:

Q: velocity of 34 rad.s1. Disk E has a weight of 65 lb : is initially at rest when it is brought into…

A: There are two types of forces that are acting on a circular surface. One type of force is Radial…

Q: The 184-lb exerciser is beginning to execute a bicep curl. When in the position shown with his right…

A: Given data WE=184lb Wb=18lb a=0.2g

Q: Disk D turns with a constant clockwise angular velocity of 34 rad.s1. Disk E has a weight of 65 lb…

A: Given t=4sω=34rad/sW=65lb Free Body Diagram

Q: If the given system is released from rest in the position shown, calculate the velocity of B when it…

A:

Q: Two identical homogeneous 30-pound cylinders are connected with a cable. Calculate the tension in…

A: The weight of both cylinders, The radius of both cylinders, The disc roll without slipping

Q: Disk D turns with a constant clockwise angular velocity of 36 rad/s. Disk E has a weight of 60 lb…

A: Introduction In this problem, we will calculate the time necessary for disc E to achieve the same…

Q: The 160-lb exerciser is beginning to execute a bicep curl. When in the position shown with his right…

A:

Q: At the instant 0-55, the boy's center of mass Gis momentarily at rest. (Elgure 1) Part A Determine…

A: θ= 55∘Weight, W= 65 lbr= 10 ft

Q: 3. The coefficients of friction between the load A and the bed of the utility vehicle are us = 0.4…

A:

Q: value of h will be

A: Given: Figure shows a schematic diagram of simple watt governor mechanismwith spindle o1o2 rotating…

Q: The 6-lb suitcase slides down the curved ramp for which the coefficient of kinetic friction is Hk =…

A:

Q: Block A is subjected to a force P of 25 lb, determine the acceleration of block B without…

A:

Q: H.W: Referring to figure shown, assuming smooth surfaces and frictionless. Pulley, calculate: 1- The…

A: The problem is based on classical mechanics and can be solved as:

Q: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to…

A: Given data: k=2 kN/mm=16 kg Need to determine the maximum velocity of the block.

Q: The uniform 15-kg bar is supported on the horizontal surface at A by a small roller of negligible…

A:

Q: The 5-kg cylinder is initially at rest when it is placed in contact with the wall B and the rotor at…

A: Given Mass of the cylinder = 5 kg Angular velocity = 6 rad/s Coefficient of the friction = 0.2 To…

Q: B 100 On a slope, the 1.3-tonne engine with an almost constant thrust of 300 N is driven by its…

A:

Q: 3. Two masses, mA = 2.0 kg and mB = 7.0 kg, are on inclines as shown and are connected by a massless…

A:

Q: When the normal force N and friction force F be in the position shown, it means that the body is…

A: Considering the equilibrium of the given body in provided figure.  If friction is static friction on…

Q: A block of mass m is released from rest at the top of an incline that makes an angle a with the…

A: Given: Mass of block is, m Weight of the body is ,W=mg . The body is release from an rest from top…

Q: Problem 6: The rear wheels of the truck shown provide traction force of 2000 N. If the truck has a…

A:

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.