1) (Re)solve the cantilever beam problem from class using the Rayleigh-Ritz Method with a kinematically admissible trigonometric function. Overlay your functions for displacement, bending moment, and shear. Po E,I,L

Q: 0 W→ क्र h₂ F

A: h1= 1.05 mh2=0.25 mw=0.50 mF=210Nto determine the magnitude of moment of Force about point O.

Q: On bar BD, what is the x component of the force at B? A. (include units with answer) On bar BD, what…

A:

Q: Draw a free body diagram

A:

Q: Determine the moment of force about A) point O and B) point P. Express the result as a Cartesian…

A: Given data: F→=-6i+3j+8k kN Need to determine the moment about the points O and P.

Q: b) Find the length CF, length GF, angle 01 and 02 for the diagram below. 5 kN

A: Consider the diagram shown below for the given truss.

Q: A simple structure is composed of two links AB and AC connected together, as shown in the figure…

A:

Q: ▸ An incompressible Newtonian fluid flows between two parallel plates (distance b). The bottom plate…

A:

Q: Problem 2) A pipe configuration is presented in the figure below. The support at point A is fixed.…

A:

Q: 1. A 100lb weight is suspended by three cables as shown in the figure. The ratios of the stiffness…

A: The mass of the block is m=100 lb. The ratio of stiffness of cables are in ratio AP:BP:CP=2k:k:3k

Q: f, acts at a distance of 21 from 0, distance of [9+ 4/3] fram o F₂ acts at a → [9+%] - 12ft. _aft →↓…

A:

Q: 3. An ant is traveling along the edge of a helix-shaped surface and the path taken is g by 0<t<n.…

A: For solution refer below images.

Q: Draw the FBD and show all the forces Calculate force for weight (W) gl=32.174 ft/s^2 Determine…

A:

Q: Two forces F₁ = 300N and F₂ = 400 act on the screw eye hook (see Figure 5.2). Determine the angle…

A: Step 1 Given F1 = 300N F2 = 400N FR = 600N Now we know that resultant force of the two force is…

Q: A force F, F above Figure with respect to point C, using CA and TCB. Given conditions di 18N, acts…

A: Force F = 18 N d1 = 5m d2 = 8m d3 = 5m

Q: A beam is supported by a pin at point A and a cable that passes through a pulley at point D. There…

A: To find:a) The reaction force at EF and pin Ab)The internal forces at the midpoint of section AB and…

Q: 4m 400 KN 10 m B 60 KN 10 m 167 KN 17 m

A:

Q: (NOT IN SCALE) A force F, |F| 15lb, acts along the diagonal of the parallelpiped. Find the moment of…

A:

Q: A (-3,7) y, m F=6kN x, m B (10,-8)

A: The data provided in the question is as follows;The magnitude of force F=6 kNThe line diagram of the…

Q: Now, if the end of the bar marked by the red circle in the figure below is the only spot where you…

A: Whenever a triangular loading is given the the total triangular load is calculated by the area of…

Q: 3kN/m 70 3m 2m find support reactions at point A 15KN

A: Given :    To find : support reactions at point A

Q: The dimensions are of the graph are d1 = 7 cm , L1 = 6 m , d2 = 4.2 cm , and L2 = 5 m with applied…

A:

Q: Find the loading in ED GD and GC. EI, IJ, JK, and KG are equal length. A wire is attached to point G…

A: To Find: Forces in the members ED, GD, and GC = ?

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.