(1) In sand casting, the volumetric size of the pattern is: (a) bigger than, (b) the same as, or (c)smaller than the cast part(2) Machining processes include which of the following (two correct answers): (a) casting, (b)drilling, (c) extrusion, (d) forging, (e) shaping, (f), and painting?(3) Aluminum sections used for making metal doors and windows are made by which process: (a)Rolling, (b) welding, (c) extrusion, (d) turning.(4) The average flow stress is the flow stress multiplied by which of the following factors: (a) n, (b)(1-n), (c) 1/n, or (d) 1/(1+n), where n is the strain hardening exponent?(5) The strength of a brazed joint is typically (a) equal to, (b) stronger than, or (c) weaker thansoldered joint?(6) Thread cutting operation is normally performed on which one of the following machine tools:(a) drill press, (b) lathe, (c) milling machine, (d) planer, or (e shaper?

(1) In sand casting, the volumetric size of the pattern is: (a) bigger than, (b) the same as, or (c) smaller than the cast part (2) Machining processes include which of the following (two correct answers): (a) casting, (b) drilling, (c) extrusion, (d) forging, (e) shaping, (f), and painting? (3) Aluminum sections used for making metal doors and windows are made by which process: (a) Rolling, (b) welding, (c) extrusion, (d) turning.

(1) In sand casting, the volumetric size of the pattern is: (a) bigger than, (b) the same as, or (c) smaller than the cast part (2) Machining processes include which of the following (two correct answers): (a) casting, (b) drilling, (c) extrusion, (d) forging, (e) shaping, (f), and painting? (3) Aluminum sections used for making metal doors and windows are made by which process: (a) Rolling, (b) welding, (c) extrusion, (d) turning.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

(b) In casting experiments performed using a certain alloy and type of sand mould, for which n can be approximately taken as 2, it took 155 sec for a cube-shaped casting to solidify. The cube was 50 mm per side. (i) Determine the value of the mould constant in Chvorinov's rule. (ii) When the same alloy and mould type are used to make a cylindrical casting of diameter 30 mm, what is the maximum length of the cylinder if the maximum solidification time is limited to 1 minute?
12.Silica sand has which one of the following compositions: (a) A12O3, (b) SiO, (c) SiO2, or (d) SISO4? 13.A misrun is which one of the following defects in casting: (a) globules of metal becoming entrapped in the casting, (b) metal is not properly poured into the downsprue, (c) metal solidifies before filling the cavity, (d) microporosity, and (e) "pipe" formation?
Only answer question 4
EX.3//A cylindrical riser must be designed for a sand-casting mold. The casting itself is a steel rectangular plate with dimensions 7.5 cm x 12.5 cm x 2.0 cm. Previous observations have indicated that the total solidification time (TTs) for this casting =1.6 min. The cylinder for the riser will have a diameter-to-height ratio=1.0. Determine the dimensions of the riser so that its TTS = 2.0 min.
(9,00 Puanlar) A riser in the shape of a sphere is to be designed for a sand casting mold. The casting is a rectangular plate, with 8- length 50 cm, width = 35 cm, and thickness = 4 cm. If the total solidification time of the casting itself is known to be 7,5 min, determine the diameter of the riser so that it will take 30% longer for the riser to solidify. %3D Riser volume: V3(TD3)/6(D%3Ddiameter) Riser area: A=TD2 Casting volume: V-L-Wt (L-Length, W=width, t-thickness) a) 8,41 cm b) O 7,34 cm c) 6.62 cm 11,46 cm Boş bırak KÖnceki 8/43 Sonraki> Каpat
a riser in the shape of a sphere is to be designed for a sand casting mold. the casting is a rectangular plate, with length 200mm, width 100mm, and thickness 18mm. if the total solidification time of the casting itself is known to be 3.5 mm, determine the diameter of the riser so that it will take 25% longer for the riser to solidify. assume a value of 2 for ‘n’ m( the exponent in chvorinov’s rule). know the volume and surface area of a sphere.
Question: 1. The Blank For The Spool Shown In Fig. Below Is To Be Sand Cast Out Of A-319, An... 1. The blank for the spool shown in Fig. below is to be sand cast out of A-319, an aluminum casting alloy. Make a sketch of the wooden pattern for this part, and include all necessary allowances for shrinkage and machining. 12.5 mm 12.0 mm 75.0 mm 100.0 mm -
QUESTIONS 1- Describe with net sketch: a. Pattern b. Riser c. Runners d. Core 2- Compare between open mold and closed mold. 3-Explain the main Procedures of Sand Casting. 4 - What are the important properties which are essential in good molding sand? Explain in details. 5- Mention advantages and disadvantages of casting. 6- Describe types of sand mold. 7- What are the common binders of sand mold and cores? 8- Describe Desirable Mold Properties. 9- Explain two types of patterns and two pattern allowances 10- Describe with sketches shell process casting (i) Composition of sand mixture (ii) Steps in molding (iii) Advantages (iv) Limitations and (v) Applications 11- Explain with Sketch the construction and operation of a hot chamber die casting machine. 12- Compare between hot chamber die casting and hot chamber die casting. 13- What is meant of investment casting? What are the main materials used for making the investment pattern. 14- Describe various kinds of patterns in use. 15- Why…
1-In hot forming processes, the strain rate is important since deformation resistance of w.p. increases as is increased. ****** 2-The coating of interior surfaces of casting molds can aid....... 3- Based on nature of use, the cores can be classified into: 1. and 2. ..... and 4-In centrifugal casting, fine grain microstructure (resisting to corrosion, better mechanical properties) castings can be obtained because of...... 5-During manufacturing processes, the residual stresses can be arising due to three major reasons: 1......, 2...... and 3...... 6- The wheels, pulleys and flywheels can be manufacturing by...... casting. 7- The ...... of casting molds can help removing impurities and facilitating metal flow inside the molds. 8-In horizontal true centrifugal casting, a tubular products having uniform wall thickness can be obtained when...... is greater than ......
A cast iron part with a square cross section is sand casted. Its length 14 in and the sides of the square cross section-2.5 in. If the mold constant in Chvorinov's rule - 3.6 min/in², how long, in minutes, will it take the casting to solidify?
2. In the casting of steel under certain mould conditions, the mould constant in Chvorinov's rule is known to be 4.0 min/cm?, based on previous experience. The casting is a flat plate whose length is 25 cm, width is 8 cm, and thickness is 2.5 cm. Exponent n is taken to have a value of 2. Determine how long it will take for the casting to solidify.
A mould having dimensions 100 mm x 90 mm x 20 mm is filled with molten metal through a gate with height h and CS area A, the mould filling time is t1. The height is now quadrupled and the crosssectional area is halved. The corresponding filling time is t2 . What is the ratio t2/t1 ?