1) Find gm, Zi, Zo, Av.(12mS, 2.2M2, 2.7k, -32.4)+ 15VIDSS= 9 mA2.7 k OVp = - 4VVGSQ = -1.5VVoHEViZo2.2 M QZi1. 5 V

Answered: 1) Find gm, Zi, Zo, Av. (12mS, 2.2MN,…

1) Find gm, Zi, Zo, Av. (12mS, 2.2MN, 2.7k, -32.4) + 15V IDSS= 9 mA 2.7k Ω Vp = - 4V VGSQ = -1.5V Vo HE Vi Zo 2.2M 0 Zi 1. 5V +

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For the ideal-diode clipper circuit given below, VS = 12.sinwt V. a. Determine the output voltage Vout and sketch this function. b. Remove the short circuit between points x and y, and replace it with a 2k2 Resistor. Find the range of values of VS for; D1 and D2 are OFF D1 is ON and D2 is OFF D1 is OFF and D2 is ON Is it possible for both D1 and D2 to be ON? y 1kO 3V D2 VS 3kQ. Vout D1 6V
Vps = 10 V R = 0.1k02 ww -ovo R₁. Consider the Zener diode circuit shown in figure. The Zener diode voltage is Vz= 5.8V at Iz= 10mA and the Zener resistance is rz = 200. a) Find the output voltage for RL = 1k0 b) Find the change in the output voltage when the load resistance varies +ARL.
Q-3. Draw 1-V characteristics of 5 V silicon zener diode (Vz-5V) and show its parameters V Vz, Izx. Izs, Izm on the curve. Q-4. Determine the range of Road (Rmin, Rmax) that will maintain Vz at 5 volts for the circuit given below. Rs m 1.0kg V1 40 V Pzm=150mw
For the below shown rectifier configuration, find the expression for the average value of voltage across the load resistor R, if the supply voltage Vs = Vm sinwt and firing angle = a. RLOAD Vm/T Cosa Vm/TT (1+cosa) O 2Vm/TT Cosa O 2Vm/TT (1+cosa) O O O O
For the given circuit find the VRL Voltage of the load; VR Voltage in the resistance R; Iz Current of the Zener diode and the Pz Power in the Zener diode. VRL = ? Iz = ? Pz = ? If the Zener diode in the figure has an elbow tension of 0.7 V. Zener breaking voltage of VZ = - 15 V Vin = 40 V R = 1 kohm RL= 3 kohm Requirement: Take out Vth by mesh method and solve equations
In the circuit shown below. Let Vm-35 V and i-20 mA and VpQ -0.7 V: iD 3 kQ 0.8 kO Vmcos(@t)V For t Os, the current in the diode equals: Oa. 0 mA Ob. 4 mA Oc. 2 mA Od. 6 mA If t = T/4, then the current in the diode equals: Oa. 6.29 mA Ob. 5.03 mA Oc. 4,03 mA Od. 7.86 mA If t = T/2, then the current in the diode equals: Oa. 15.24 mA Ob. 13.24 mA Oc. 19.24 mA Od. 17.24 mA
in solution Yoad H.W2 The single-phase full wave controlled rectifier has a with R= 0.502 and L= 6.5mH. The input voltage V, 220V at 50Hz. The delay angle is a-60, determine: e) The average thyristor current f) The rms thyristor current g) The output rms current h) The average output current NOTE: Drive any formula that used in solution NG BRANCH
14 A0-volt forward voltage is applied to a silicon diode in series with a kond of 3 k2. Draw ihe de kud line. What is the slope of the line? Selution The value of voltage Vy across diode is given by Vy v- lR Since R and V are fixed values, this nquation can by represented by a straight line on V-ly characteristics of diode; thn is de kud foe. When I 0, maximum voltage across the diode V 30 V. This is point BC30, 0). 10 mA 30 V Fig. 2.25 Problem 2.4.
Q2) Find the Performance Parameters of a Full-Wave Rectifier with an RL Load, the single-phase full-wave rectifier of the figure below has L = 6.5 mH, R = 2.52 and E= 10 V. The input voltage is Vs = 120 V at 60 Hz. Assume that the load current is continuous current. Where: V io (t) = -(sin(wt - 0)+ im Z 2 -R 1-ewr -sin 8.e *) E R Determine: (1) The steady-state load current lo at wt = 0, (2) The average diode current Ip(av), (3) The rms diode current Ip(ms), (4) The rms output current lo(ms), and (5) The input power factor PF D₁ D₂ A Pa D₂ A + Vo 1. E
Shown below is a diode circuit. If the input signal Vs = 34 Vp-p and the DC voltage Vdc = 5 V, what is the output voltage (in volts) of the circuit during the positive alteration of the input signal? No need to show your solution. Just write your numeric answer on the space provided. Round off your answer to 2 decimal places. 1.0kn ... Vdc Vs Vo Si D1
Question: What is the desired current? Given: (see pic)
Please solve this question queckly