1- Draw a diagram between pressure and mass? 2- Draw diagram between true pressure and the in error device reading?

Q: Differential equation: Newton's law of cooling A thermometer is removed from a room where the…

A:

Q: An hydrogen vapour container is mounted with a pressure gauge which shows 10 bar. Then its absolute…

A: Pressure is a vector physical quantity that represents the amount of force acting on a unit area of…

Q: Identify the correct statement in the following. а. all intermolecular forces are neglected for…

A: The Ideal Gas Law is a useful approximation valid for gases are at low pressures and high…

Q: Determine moment of F about line AB.

A: M→=r→ x F→ M= moment vector r= position vector of the application point F = force vector

Q: What is hooke's law of elesticity introduction and conclusion in an experiment?

A: Hooke's law states that the stress is directly proportional to the strain upto the proportional…

Q: Which table is used in this question to extract Cp value?

A: To find: Which table is used in this question to extract Cp value?

Q: The energy required to raise the temperature of a unit mass of a substance by one degree is known as

A: The energy required to raise the temperature of a unit mass of a substance by one degree is known as…

Q: Transitional and rotational equilibrium with the application Please write long Answer

A: Translational and rotational equilibrium with the application : Equilibrium of motion - When a body…

Q: PROBLEM 1: A 20-ton vapor compression refrigeration system is to evaporate R-12 at -20°C and to…

A: Given: Cpaicity of the refrigeration→RC=20 ton=3.5×20=70 KW

Q: A 2-m long hollow steel shaft (G = 75 GPa) has an outside diameter of 75 mm and an inside diameter…

A:

Q: Which of the following does not belong to the group? force stress time velocity

A:

Q: What is Qh and Qc based on the table

A:

Q: Problem 3: Two forces, P and Q, are applied to the lid of a storage box as shown. If P = 35N and Q =…

A:

Q: can you please state the correct and incorrect statements based on its topic. Saturation…

A: A saturated curve has to parts: Saturated vapor curve that separates the two phase region from…

Q: Which of the following is NOT an amount of energy unit?

A: Answer:-  Option (2) None of these.

Q: 2. A beam AB is loaded as shown. The beam is pin-connected to the wall at A. At Ba 10-inch diameter…

A:

Q: How did you combine eq1 and eq2?

A:

Q: 50 3X Ø12 R12 25 RIB Top view METRIC R50 R18 Ø 20 R22 RI25 10 110- Front view

A: isometric projection is a method for representing three dimensional object into two dimensional…

Q: What is the mechanical advantage of this system?

A: We have to first draw free body diagram of the block and the pulleys and then derive a relationship…

Q: Example procedure of Level, Flow, Pressure and Temperature control system in mechanical engineering

A: Given: Briefly explain level, flow, pressure, and temperature control system example procedure.

Q: 7.10 If 2 kg of steam at 18 bar and 288°C undergo a constant pressure process until the quality…

A:

Q: identify the correct statement O a. intermolecular forces is not considered, always in real gas…

A: The real gas equation / Vanderwaal equation is given as  (P+an2V2)(V-nb) = nRT here a and b are…

Q: Describe the process of Calculating Temperature: Calorimetry with an Ideal Gas?

A: Calorimetry is a technique that is used for measuring the enthalpy changes during any chemical…

Q: 1. Determine the force F to maintain the bell crank shown in equilibrium. Neglect friction at Pivot…

A:

Q: choose one mass analyser from the following – quadrupole, time of  flight, ion trap, FT-ICR,…

A: Given:Select any mass analyser.To find:Write the principle of opeartion, pros, cons, and…

Q: can you make a table for volume/pressure/temp/u/vr values?

A: Properties Stage 1Stage 2Stage 3Stage 4volume (cm3)40032003200400pressure…

Q: Pre-Condition Post-Condition Weakest Pre-Condition \sStrongest Pre-Condition

A:

Q: Radiation testing in automotive

A: The radiation testing is given

Q: The ___________ is whatever we want to study  it may be simple as a free body as  complex as an…

A: Answer (1) Option (c) system . is correct option. Explanation It is a fixed mass or a region in…

Q: Identify Kelvin-Planck Statement for the Second Law of Thermodynamics.

A: Kelvin-plank statement Second law of thermodynamics has two statements as kelvin-plant statement and…

Q: Which of the following statements best describe for a typical diatomic molecule of an ideal gas eg.…

A: Atoms are made up of a single positive nucleus surrounded by a cloud of negatively charged…

Q: Identify, which is not correct from the diagram Select one: O a. 2-3 and 4-1 = constant pressure…

A:

Q: Question 2 Z 0.8 cm P 1.2 cm 0.9 cm The force P = 3640 N acts along line BD. Determine the moment of…

A: To find; The moment of force P about axis OA. Given: The force acts along the line BD is P=3640 N.…