Please help with problem number one 1) Determine the time required for a car to travel 1km assuming it begins andends its travel at rest, and can accelerate at 1.5m/s? and decelerate at2.0m/s?.2) A stone A is dropped from rest down a well, and 1 s later another stone Bis dropped from rest. Determine the distance between the stones anothersecond later.Partial Ans. As = 48.3 ft3) Consider a particle whose velocity is given with v(t) = 3t2 – 6t ft/s, wheret is in seconds. If s(0) = 4 ft, determine the position of the particle att = 4 s. What is the total distance traveled in those four seconds?Partial Ans. s;otal = 24 ft.

Answered: Image /qna-images/answer/fa8aa47a-ba1c-403b-aa6e-d4e103f01923.jpg

Answered: 1) Determine the time required for a…

1) Determine the time required for a car to travel 1km assuming it begins and ends its travel at rest, and can accelerate at 1.5m/s? and decelerate at 2.0m/s?.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

how do i draw sectional view of this object.
I am attaching both questions for 4 and 5 with the question in the image. thank you. NOTE : So the last person answered this question WITHOUT refencing the answer for whether question 4 or 5 answeres were given, so i am asking for question 5(or the answer for the question that was NOT solved because it was not referenced.) These were the following answers given to me from the last person on bartleby who answered my question without referencing whether it was the answer for question 4 or 5. 1 pass 2 fail 3 fail 4 pass
please show all the work with diagrams
Number 4
Provide a demonstrated drawing of the figure (construct) as well
LESSON: AUTODESK FUSION 360 Identify the feature displayed in the picture, and choose from choices below. Extrude Sketch Revolve Hole Pattern Create Form Press Pull Fillet Shell Combine Split Body Move Offset Plane Measure Canvas Select Windows Selection Crossing Selection Freeform Selection Paint Selection
Diagram: Given the hook-up drawing, list all the equipment, tools and materials that are needed in installation. INST. PIPING 1- *1 INST. PIPING
Paula has worked for Brindle Corporation for 3 years. During this time, she has worked as a machine operator/cell leader in various work cells. Recently, the plant went to mandatory 12-hour shifts and plans to remain on this schedule for several months. Paula’s present work cell is manufacturing 3-inch diameter exhaust tubes that are made from stainless steel. These tubes get a hole punched in them, a flange welded on, and burrs ground off. The pipe then gets placed into a gage to check that it was made correctly. (The tubes weigh about six pounds.) Paula has been performing the welding operation. She leans into the machine and loads the part into a fixture then positions the flange. Both pieces are clamped (using hand clamps) into position and the machine is cycled by depressing two palm buttons. The gaging operation requires placing the finished part into the gage and clamping it (using hand clamps) into place. A pin is depressed to verify the position of the hole and a…
Paula has worked for Brindle Corporation for 3 years. During this time, she has worked as a machine operator/cell leader in various work cells. Recently, the plant went to mandatory 12-hour shifts and plans to remain on this schedule for several months. Paula’s present work cell is manufacturing 3-inch diameter exhaust tubes that are made from stainless steel. These tubes get a hole punched in them, a flange welded on, and burrs ground off. The pipe then gets placed into a gage to check that it was made correctly. (The tubes weigh about six pounds.) Paula has been performing the welding operation. She leans into the machine and loads the part into a fixture then positions the flange. Both pieces are clamped (using hand clamps) into position and the machine is cycled by depressing two palm buttons. The gaging operation requires placing the finished part into the gage and clamping it (using hand clamps) into place. A pin is depressed to verify the position of the hole and a…
Project is a program designed to user application that may be simple .or complex True False O
TYPEWRITTEN ONLY PLEASE UPVOTE. DOWNVOTE FOR HANDWRITTEN. DO NOT ANSWER IF YOU ALREADY ANSWERED THIS
Please solve it complete please don't copy paste