b) 1) Design (Find R₁, RF, and R) the sawtooth-wave generator to have an output frequency fo = 6kHz. Assume Vth = |-Vth = 5V, Vsat = |-V sat | = 14V, and Vref= -9V.Assume the value of C = 0.04µF.2) Determine duty cycle (k).3)Draw the design circuit and output waveform.

We have to deign parameters for sawtooth generator Given f0 =6 kHz Vth =5 V Vsat =14 V V ref =-9 V…

1) Design (Find R₁, RF, and R) the sawtooth-wave generator to have an output frequency fo= 6kHz. Assume Vth = = 1- Vth | = 5V, Vsat = |-V sat = 14V, and Vref= -9V.Assume the value of C = 0.04µF. 2) Determine duty cycle (k). 3) Draw the design circuit and output waveform.

1) Design (Find R₁, RF, and R) the sawtooth-wave generator to have an output frequency fo= 6kHz. Assume Vth = = 1- Vth | = 5V, Vsat = |-V sat = 14V, and Vref= -9V.Assume the value of C = 0.04µF. 2) Determine duty cycle (k). 3) Draw the design circuit and output waveform.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A schematic design of a full-wave bridge type power supply is given below. Provide the appropriate values for the inductors, diodes, capacitor and resistors, such that the output DC voltage is 7.5 V and the max. output power for the load resistance is 20 mW (percentage error for output voltage and output power is 2%). AC voltage source: Amplitude=311.13, Freq=60, DC offset= 0. For the rectifier part, choose diodes with an appropriate PIV rating. Show all the formulas and computations involved in acquiring the values for the inductors, diodes, capacitor and resistors. • In choosing your Zener diode, consider the output voltage and the output current. Note that the output current should be the minimum Zener current. • For the value of the series resistor RS, choose a lower value for less ripple but always consider the required output voltage. •The ripple voltage peak-to-peak value should be less than or equal to 1% of the required output voltage. Use the formula below for choosing the…
A schematic design of a full-wave bridge type power supply is given below. Provide the appropriate values for the inductors, diodes, capacitor and resistors, such that the output DC voltage is 6.2 V and the max. output power for the load resistance is 20 mW (percentage error for output voltage and output power is 2%). AC voltage source: Amplitude=311.13, Freq=60, DC offset= 0. For the rectifier part, choose diodes with an appropriate PIV rating. Show all the formulas and computations involved in acquiring the values for the inductors, diodes, capacitor and resistors. In choosing your Zener diode, consider the output voltage and the output current. Note that the output current should be the minimum Zener current. For the value of the series resistor RS, choose a lower value for less ripple but always consider the required output voltage. The ripple voltage peak-to-peak value should be less than or equal to 1% of the required output voltage. Use the formula below for choosing the value…
ument-460F8C6BE9D6- x 5-1.pdf CD Page view A Read aloud 1: Theory 1.1 Describe briefly a sinusoidal signal and ALL its properties. Give example with figures. ongingoring which is si +.
A phase modulator has kp= 2.8rad/V. What rms voltage of a sine wave causes a peak phase deviation of 74°? Determine the peak phase deviation for a PM modulator with deviation sensitivity K = 3.8 rad/V and a modulating signal vm= 12 sin(2π1000t).
Q.2) Determine all values of resistors and capacitor for the triangular waveform generator whose output alternates between +10Vpeak and -10V peak when the input is a 10-Hz square wave that alternates between +2V and -2V. The input resistance to the generator must be at least 15 kQ. you may assume that there is no de component or offset in the input.
2. Write an OCTAVE program to plot the signal given below P=Pmax Sin(2πft); where Pmax=10 MW, f=60 Hz Find out time.peniod and verify it with graph. Assume necessary data.
For the following waveforms, determine the average, effective, peak factor and form factor.D.)A square wave having a positive maximum value of Em and a negative maximum value of −Em.
H.W For general pulse train shown below: A sin (nw,t) 2 A 1, show that ; Dn = 2. for a duty cyele %3D shou that : AT %3D Sinc (nT) To To 3. for a duty syele : To & A= 1 %3D Find Dn .
The pulse voltage waveform displayed on a CRO, is shown in figure given below. Find, (a) Frequency. (b) Magnitude of the pulse. (c) The amplitude. 21 0.5 5 0.2 10 20-(Vicm 5 ms 100 us 50 ms time/om 500 ms 30- 40 50 2s
Use multi-vibration circuits and create a signal generator that produces a square, triangular, and sinusoidal waveform with a frequency of 1kHz. Show work for theoretical layout. Also, use a switch for each waveform.
For the following waveforms, determine the average, effective, peak factor and form factor.G.)A semi – circular wave having a positive maximum value of Em and a negative maximum value of −Em.
For the following waveforms, determine the average, effective, peak factor and form factor.E.)A triangular wave having a positive maximum value of Em and a negative maximum value of −Em.