1) calculate axil force due to dead and live load in three different columns A1, A2, C3 2) Design column A2 using reinforced concrete and steel.   DL= 6       LL=3.5    Please use the British code.

Q: For the beam shown, determine the tensile development length required for the epoxy coated bars if…

A:

Q: A circular column, 60 in. in diameter is reinforced with 48 #14 longitudinal bars and #4 ties at 9…

A: According to given data A circular column, 60 in. in diameter  reinforced with 48 #14 longitudinal…

Q: The building construction is cast-in-place conventionally reinforced concrete. What is the maximum…

A: This question is related to the Design of RCC structure from Civil Engineering. In this question ask…

Q: What is the collapse load of beam as shown in figure? A B 10Mp L 12M₂ L 3M, 1/2 W C D M₂ 1/2 16Mp L…

A:

Q: 1. A rectangular section column b= 300 mm, h = 400 mm. The calculated length lo=3m, the design value…

A:

Q: A beam section is limited to a width of 250 mm, and total depth h=550 mm, and has to resist a…

A:

Q: iv. What is the girder average weight (in pounds per sq ft)? e. Write the calculated average weights…

A: As per Bartleby's guidelines we are supposed to answer only first three questions. Kindly repost…

Q: 4. Given the following properties of T-beam Effective flange width (b).......1200 mm Width if the…

A:

Q: Problem 1: Determine the allowable service live load, PL assume the dead load is due to the beam…

A: The service load PL is required.Given, Width, b = 10"Effective depth, h = 25"The span length, L =…

Q: 3. Load Tracing For the framing plan below, find out the reactions of the beams and girders shown in…

A:

Q: Wo does not include beam weight PL=lo kiPs = 2 kip/ft W = 4 kip/ft %3D 3 # 11 bars (A) 2 in.…

A: Compressive strength of concrete (fc') = 5000 psiYield strength of steel (fy) = 60000 psiUnit weight…

Q: 30" Check if the following T-beams satisfy the ACI requirements for T-beams. Regardless of your…

A:

Q: The beam shown below is subjected to a factored uniform load of 8 kips/ft. The concrete strength is…

A: Shear strength of the beam Shear strength refers to a material or component's resistance to a…

Q: Using the following parameters for a square tied column, f'c = 21 MPa longitudinal reinforcement =…

A: Given: Axial load: DL = 900 kN LL = 700 kN f'c = 21 MPa fy = 415 MPa longitudinal bar = 25 mm Steel…

Q: Problem 3. $40. Design a rectangular beam to carry the load show, in addition to its self-weight.…

A: Given data f'c = 4000 psi fy = 60000 psi Unit weight of concrete = 150 pcf Dead Load WD = 3 k/ft…

Q: List at least three variables (structures) that affect the loss of heating and cooling in the…

A: Brief concept- Loss of heating and cooling in the building is a very essential part of the air…

Q: Using an interaction diagram Design Aid for a 24-inch square column with 4000 psi concrete, with…

A: Given data Square columnAg=24*24in=576in2f'c=4000psi,fy=60000psiγ=0.910 number ofbars to be used on…

Q: A cantilever beam is reinforced with 4-#9 epoxy coated reinforcing bars, determine the length…

A: Hi there!! since you have asked multiple questions, we will solve the first question for you. If you…

Q: Please solve using paper.Problem 7. The concrete pier is subjected to soil pressure that causes the…

A:

Q: Problem 6.3 A short column is made by nailing four 1 x 4-in. planks to a 4x4-in. timber. Using an…

A: Given data : Allowable stress = 600 psi To Find : Determine the largest load P that can be applied…

Q: Find the axial load resistance of the tied short column shown below and check all code requirements.…

A: b = 350 mm h = 350 mm fc = 30 MPa fy = 400 MPa Main bars, 8-20mm

Q: 4. A compression member 3 m long consist of two angles 150 x 100 x 10 mm with long legs back to back…

A: A compression member 3 m long consists of two angles 150 x 100 x 10 mm with long legs back to back…

Q: 8. For a section 6 inches wide and 14 inches deep, and a cover of 2 inches, what is the maximum safe…

A:

Design criteria for structural loading

The different loads such as loads due to self-weight (dead load) and external loads such as live load, wind loads, seismic load, snow load, and other loads and load combinations that influence the design of a building are called structural loading. The nature of the applied load differs from changes in the location, design, and type of materials used. The design criteria require that structures must be designed and constructed to be able to withstand all load types that are expected to act upon the structure and render its usage for the designated purpose. The structural members such as beams, slabs, columns, and foundations help the structure to withstand the applied load. There are different institutes such as ASCE and ACI that provide building design codes to assure minimum safety requirements and quality of the structures.