There can be 1 or 2 answer in a single mcq please answer all as soon as possible 1) A Diesel engine is aO reciprocating spark ignition engine.O rotary spark ignition engine.O reciprocating compression ignition engine.O rotary compression ignition engine.2) An IC engine in which air or the fuel-air mixture is introduced into the combustion chamber at a pressure near to the atmospheric pressure iscalled aO pressurized enginecompressed engineO supercharged engineO naturally aspirated engine3) Thetypically provides the structural support to withstand the mechanical and thermal loads in an IC engine.O cylinder headO crankcaseO cylinder blockO camshaft4) Which one of the following is TRUE about a wet cylinder sleeve?O It is in direct contact with the coolant and thinner than a dry sleeveO It is thicker than a dry sleeve and in direct contact with the coolant.O It is thicker than a dry sleeve and not in direct contact with the coolant.O It is thinner than a dry sleeve and does not offer significant structural support.5) The ratio of the crankshaft offset to the distance travelled by the piston in one stroke is equal toO05010204

Diesel engine is a reciprocating compression ignition engine. Spark ignition engines are petrol…

Answered: 1) A Diesel engine is a O reciprocating…

1) A Diesel engine is a O reciprocating spark ignition engine. O rotary spark ignition engine. O reciprocating compression ignition engine. O rotary compression ignition engine.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

I asked for problems 6 and 7 to be answered, but I did not get a properly structured answered as the example shows on problem number 1. Here is the link to the questions I already had answered, could you please rewrite the answer so its properly answered as the example shows (Problem 1)? https://www.bartleby.com/questions-and-answers/it-vivch-print-reading-for-industry-228-class-date-name-review-activity-112-for-each-local-note-or-c/cadc3f7b-2c2f-4471-842b-5a84bf505857
I am attaching both questions for 4 and 5 with the question in the image. thank you. NOTE : So the last person answered this question WITHOUT refencing the answer for whether question 4 or 5 answeres were given, so i am asking for question 5(or the answer for the question that was NOT solved because it was not referenced.) These were the following answers given to me from the last person on bartleby who answered my question without referencing whether it was the answer for question 4 or 5. 1 pass 2 fail 3 fail 4 pass
follow up question - for the past two question. (subquestions)
i need the answer quickly
Write down the Part Programming codes for the First alphabet of student (S) in capital Type: Engraving operation
LESSON: AUTODESK AUTOCAD Choose from the choices:
Follow the instructions. Typewritten for upvote. No upvote for handwritten. Thank you
If a critical point at structural element is subjected to the stress shown on the 2D element, determine the factor of safety (FS) against rupture according to the maximum principal stress theory. The material has an ultimate tensile stress Sult = 500 Mpa. 150 Mpa 50 Mpa 250 Mpa
Plz solve neatly and correctly showing all steps
hand written plz Answer the following questions using the information provided in this unit. Know and Understand 1. True or False? The primary purpose of section views is to help feature exterior detail without using hidden lines. For the next three terms, match the three types of lines to the three descriptions. Answers are used only once. 2. Cutting-plane line 3. Section line 4. Short break line A. Not exclusive to section views, but needed for broken- out sections. B. Drawn thick in a view adjacent to the section view. C. Drawn thin, and usually continuous, but sometimes dashed. 5. Of the following, which is not a type of section view featured in this unit? A. Full B. Half C. Quarter D. Offset 6. True or False? The preferred dividing line between the two halves of a half-section view is the visible line. 7. An object with a number of odd features, such as spokes or holes, often has a(n) section so the odd features can be rotated around the axis into a vertical cutting plane,…
Project is a program designed to user application that may be simple .or complex True False O
Problem-AA: Consider the following system of equations: -123 = 1.5a + 25n 5 = -21a +n Calculate the two unknows.