1 A converging-diverging nozzle has a throat area of 0.002 m? and an exit area of 0.0077 m?. The upstream air reservoir has stagnation pressure and temperature conditions: po=1000 kPa and To=500 K. The gas constant for air is 287 J/ kg K and its ratio of specific heats is 1.4. What is mass flow rate out of this nozzle when it operates in choked flow conditions?

1 A converging-diverging nozzle has a throat area of 0.002 m? and an exit area of 0.0077 m?. The upstream air reservoir has stagnation pressure and temperature conditions: po=1000 kPa and To=500 K. The gas constant for air is 287 J/ kg K and its ratio of specific heats is 1.4. What is mass flow rate out of this nozzle when it operates in choked flow conditions?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Estimate the mass flow rate and Mach number at the discharged duct when an air flows through a 6cm…

Q: Air at 800 kPa and 1200 K enters a converging nozzle with negligible velocity (i.e., these are…

Q: Air enters a convergent-divergent nozzle having a throat area of 930 cm2 and attains a Mach number…

Q: Shock waves are treated as discontinuities here, but theyactually have a very small fi nite…

A: The variation of the velocity, temperature, pressure and entropy of the before and after the shock…

Q: at 30°C and 101 kPa is drawn th ith throat area 0.025 m² and exi ge vacuum tank. Determine the

A: Given: po=101kPaTo=30oC

Q: Steam enters a nozzle at 377°C, 1.6 MPa, and a steadyspeed of 200 m/s and accelerates isentropically…

A: At saturation condition, steam is not ideal, Use the steam tables; Write the properties of stram at…

Q: ?. Calculate and plot the exit pressure, exit velocity, and mass flow rate versus back pressure…

A: Exit density, P_{e} = P_{e}/(R*T_{e}) = (422.64 * 10 ^ 3)/(287 * 996) P_{e} = 1.4785 kg/m^ 3 •…

Q: Q1) Air enters a converging-diverging nozzle as shown in the Figure. 1 . Determine : The…

Q: A test section in a wind tunnel is at Ma = 2.5, T = 15 °C, and P = 35 kPa (abs). The fluid is air.…

Q: A converging-diverging nozzle discharges air into a receiver where the static pressure is 1.034 105…

A: Introduction: A nozzle is a variable cross-sectional area tube used to increase the speed of an…

Q: A compressed Air enters a convergent-divergent nozzle, at 4.0 atm, 300 K and at Mach 2.0. The nozzle…

A: Note: Since you have posted a question with multiple sub-parts, we will solve first three sub- parts…

Q: Discuss Nozzle efficiency and Stagnation Conditions

Q: Air flows in a constant-area duct as shown in the figure. Assume Rayleigh line flow and the air to…

A: “Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: P1 = 140 kPa and the manometer fluid is oil (SG = 0.85). Neglect losses. (a) Estimate the pressure…

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Steam which is at a pressure of 3 Bar ond dry saturoteu expands in a convergent nozzie to a pressure of 2 Bar. The area of throat is 3 cm. Negiecting approach velocity, calculate the exit velocity and mass fiow rate if (a) Equilibrium flow is assumed (b) Supersaturated flow is assumed.
Figure shows a 100 kg concrete cylinder resting on a wall at A. A 10° wedge is used at the bottom to prevent the concrete cylinder from rolling. The coefficients of static friction at A and B are 0.6 and 0.2, respectively, and the coefficient of static friction between the wedge and the floor is 0.3. By assuming the negligible weight of the wedge, determine the force P required to lift the concrete cylinder in the direction shown.
An air nozzle has an exit area 1.6 times the throat area. If a normal shock occurs at a plane where the area is 1.2 times the throat area, find the pressure, temperature, and Mach number at the exit. The stagnation temperature and pressure before the shock are 310K and 700KP..
The exit cross-sectional-area of a converging nozzle (mo= 6 kgs-1, To= 227.74 K, po=199.26 kPa, v1= 190 ms-1, pb= 90 kPa),
Air flows steadily from a tank through the pipe inFig. . There is a converging nozzle on the end. Ifthe mass flow is 3 kg/s and the nozzle is choked, estimate(a) the Mach number at section 1 and (b) the pressureinside the tank.
Don't use shift solve
Q1> Air at 30 C and 101 Pa is drawn through a covergent-divergent nczze with thrcat area 0.025 m² and exit area 0.0724 m², discharging into a large vacuun tank. Determíne the conditions (a) upstream and b) dourstrearm of a normal shock which is positioned at the nozzie exit
mnot Thot = 75°C Tout-? mcold Tcotd = 18°C -- Hot and cold stream of water are mixing together as shown in Figure. The temperature of the hot 6. and cold streams at the inlet are 75 °C and 18 °C, respectively. Mass flow rates of the hot and the -- cold streams are (5.0000x10^-2) kg and (1.00x10^-1) kg, respectively. Find the temperature of the mixed stream. The specific heat of the hot water stream is 4000 J/kg-K and the cold stream is 3800 J/kg-K. Answer should be in °C with three significant figures. Note: Your answer is assumed to be reduced to the highest power possible. Your Answer: x10 Answer DELL F5 F7 F9 F10 F11 F12 PrtScr Delete F6 F8 Insert
Air flows at the rate of 0.8 kg/s through a convergent-divergent nozzle. The entrance area is 0.004 m? and the inlet temperature and pressure are 300 K and 400 kPa. If the exit pressure is 140 kPa and the expansion is isentropic, find: The velocity at entrance, The stagnation temperature and stagnation pressure, The throat and exit areas, The exit velocity.
(7) The mass flow rate from a converging-diverging nozzle (Ae= 0.02 m2, po= 200 kPa, To= 345 K, pb= 160 kPa), * 7.1 kgs-1 7.1x10-3 kgs-1 8.7 kgs-1 8.7x10-3 kgs-1
Air enters a converging-diverging nozzle with negligible velocity. As an engineer, you need to design the nozzle to achieve the outlet temperature of not exceeding 600 K. State ALL assumptions with justification and details calculations. (Some imcomplete details can just beassumed in order to get the answer)
-Converging nozzle is supplied with Po=10 bars and To=1000 K and discharges to atmosphere with pressure of 3.6 bars and the nozzle exit area is 10 cm. The pressure at nozzle exit will be: Select one: O a. Pe=7.45 bars O b. Pe=D4.00 bars O c. Pe-6.55 bars O d. Pe=5.28 bars