06 A convolutional circuit has three internal registers (S0, S1, and s2), and two outputs (CO and c1), calculated asfollows: c0=i+s0; c1=i+50+s1. We are currently in state 110 and receive input 1. What is the output and next state?O c0=0; c1=1; next=111c0=0; c1=0; next=111c0=1; c1=0; next=111c0=1; c1=1; next=111QUESTION 835 A convolutional circuit has three internal registers (S0, S1, and s2), and two outputs (co and c1), calculated asfollows: c0=i+s2; c1=i+50+s1. We are currently in state 110 and receive input 0. What is the output and next state?c0=0; c1=0; next=011c0=1; c1=0; next=011c0=1; c1=1; next=011c0=0; c1=1; next=011 21 A convolutional circuit has three internal registers (S0, S1, and s2), and two outputs (c0 and c1), calculated asfollows: c0=i+s1; c1=i+50+s2. We are currently in state 100 and receive input 0. What is the output and next state?c0=1; c1=0; next=010c0=0; c1=1; next=010c0=1; c1=1; next=010c0=0; c1=0; next-010

This question presents a convolutional circuit with three internal registers and two outputs. The…

06 A convolutional circuit has three internal registers (S0, S1, and s2), and two outputs (CO and c1), calculated as follows: c0=i+s0; c1=i+50+s1. We are currently in state 110 and receive input 1. What is the output and next state? O c0=0; c1=1; next=111 c0=0; c1=0; next=111 c0=1; c1=0; next=111 c0=1; c1=1; next=111

06 A convolutional circuit has three internal registers (S0, S1, and s2), and two outputs (CO and c1), calculated as follows: c0=i+s0; c1=i+50+s1. We are currently in state 110 and receive input 1. What is the output and next state? O c0=0; c1=1; next=111 c0=0; c1=0; next=111 c0=1; c1=0; next=111 c0=1; c1=1; next=111

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

QUESTION 5 35 A convolutional circuit has three internal registers (s0, s1, and s2), and two outputs (c0 and c1), calculated as follows: c0=i+s2; c1=i+s0+s1. We are currently in state 110 and receive input 0. What is the output and next state? O c0=0; c1=0; next=011 O c0=1; c1=0; next=011 O c0=1; c1=1; next=011 O c0=0; c1=1; next=011 QUESTION 6 11 A convolutional circuit has three internal registers (S0, S1, and s2), and two outputs (c0 and c1), calculated as follows: c0=i+s0; c1=i+s1+s2. We are currently in state 110 and receive input 0. What is the output and next state? O c0=1; c1=1; next=011 O c0=0; c1=1; next=011 O c0=0; c1=0; next=011 O c0=1; c1=0; next=011 QUESTION 7 02 A convolutional circuit has three internal registers (s0, s1, and s2), and two outputs (c0 and c1), calculated as follows: c0=i+s0; c1=i+s0+s1. We are currently in state 011 and receive input 1. What is the output and next state? O c0=0; c1=1; next=101 O c0=0; c1=0; next=101 O c0=1; c1=0; next=101 O c0=1; c1=1;…
1. Given the following circuit: 5 ns D. 1ons The gate delays are as shown above the gates. A, B, C are three input, and all of them are varying, as given below: A = 0 at time 0, and stays constant until time = 20 ns, when it changes to 1 and stays constant there after B = 1 at time = 0, and stays at 1 value until time = 35 ns, and then changes to 0 at35 ns, and stays constant after that. !3! %3D C= 0 at time 0 and changes to 1 at 50ns Plot A, B, C upto time = 70 ns.
9. A multiplexer is a switching circuit that produces as its single output one of a set of inputs based on the value of some additional inputs called the controls. Given that 0, 1, 2, and 3 in two-bit binary are 00, 01, 10, and 11, respectively, draw a 2-bit multiplexer using the three basic logic gates with inputs xo, x1, x2, and x3, and two control inputs co and c1. Setup the circuit so that x; is the single output, where i if the value of the 2-bit integer (cico)2. NOTE: This is not a Boolean product; instead it's the binary representation of an integer where c1 is the most significant bit and co is the least significant bit.
The circuit below is a 4-bit shifter with 2 control inputs s1 and s0, 4 data inputs 13, 12, 11, and 10, and 4 data outputs Q3, Q2, Q1, and Q0. If the input 13 12 11 10 = 1101, what is the final output when s1 s0 = 01 and then 11 next clock cycle ? 13 12 I1 IO s1 s0 Q3 Q2 Q1 QO 0000 0010 0110 O 1010
• Design a sequential circuit with two T Flip Flops, A and B, and two inputs, E and x. If E=0, the circuit remains in the same state regardless of the value of x. When E=1 and x=1, the circuit goes through the state transitions from 00 to 01 to 10 to 11 back to 00, and repeats. When E=1 and x=0, the circuit goes through the state transition from 00 to 11 to 10 to 01 back to 00, and repeats
Consider a special purpose decoder that is called BCD to seven-segment decoder. The decoder takes a 4-bit Binary Coded Decimal (BCD) number X3 X2 X4 X0 (0-9) and produces 7 outputs a, b, c, d, e, f, and g The specification of this circuit is as follows: ⚫ The 7 outputs of the decoder are connected to LED segments as shown in the figure below. The LEDs are active low, ie, the LED emits light when it is connected to logic 0. • The decoder output is determined in a way so that the LED segments display the decimal representation of the input. For example, if the input X3 X2 X1 X0 is 0001 respectively (which is equivalent to decimal 1), the outputs a, b, c, d, e, f, and gare 1001111 showing the letter 1 on the display (remember the LEDs are active low). Decoder W- 4x7 e U Answer the following questions: a. Fill in the truth table of that decoder. Choose a good value for the output when the input is greater than decimal 9. b. Derive the simplified Boolean expressions for the outputs a, b, c,…
Computer Science Design combinational logic for outputting the wait time associated with each state. For example, state 000 has the main street green light on for 15 seconds. The combinational logic for the input 000 would have an output 1111 corresponding to decimal 15. Let the outputs W3, W2, W1 and W0 represent a binary number corresponding to the wait time.
= 1 causes the heater to decrease its Q3: A Moore sequential circuit has three inputs (X2, X1, and Xo) that specify a temperature range in a room. The circuit has two outputs (I and D) that control a heater for the room; I = 1 causes the heater to increase its heat output, and D heat output. If the temperature range is 0, 1, or 2 for three successive clock cycles, the circuit generates I = 1, and conversely if the temperature range is 5, 6, or 7 for three successive clock cycles, the circuit generates D = 1; otherwise, I = 0 and D = 0. 1. Draw a state diagram. 2. Construct a state table. 3. Using D flip-flops, construct a state assigned table. 4. Determine the next-state and output logic expressions. 5. Sketch the corresponding logic circuit.
2. Design a combinational circuit with three inputs, x, y, and z, and three outputs, A, B, and C. When the binary input represents any of the decimal digits 1, 2, 3, or 6, the binary output should represent the decimal digit that is one greater than the input, that is 2, 3, 4 and 7, respectively. Similarly, when the binary input represents any of the digits 4, or 7, the binary output should represent the digit that is two less than the input. The remaining two inputs, that are the binary representations of the decimal digits 0 and 5 never occur. Draw the truth table, and give all the minimal forms for the functions that represent the outputs A, B, and C. U
The State Diagram shown below corresponds to the circuit shown at left. (the x in the diagram corresponds to a don't care, it can be either 0 or 1) OO (M) True False T₁ q₁ 0 1₂ 10 00 ola 01 11
Design a circuit that takes three bits, X2, X1, X0 as input and produces one output, F. F is 1 if and only if 2<=X<=5 when X = (X2, X1, X0) is read as an unsigned integer. For example, if X2=1, X1=0, and X0=0, then the unsigned binary value is 100, which is 4, so the output would be 1. Your Assignment For This Problem Includes the Following Design the necessary circuit using Logisim to implement the situation described above. Use Kmaps for simplification. Be VERY careful to get the correct functions for your output before simplifying and designing the circuit with Logisim. You should minimize the circuit. Your circuit should have three inputs and one LED output. All inputs (X2, X1, X0) and output (F) should be labeled (in Logisim, not by hand). Please use these names to indicate the inputs and output so all projects are consistent. You should also include your name as a label on the circuit. Test your circuit to be sure it is working correctly.