03(5 marks ): A control system is shown in Fig.Q3. Determine an appropriate gain K so that the steady state error to a unit step input is zero. ess C() Esso R(s) (s+2) (s+4)

Q: difference between measurement uncertanty and measurement error

A: Given : Need to find the difference between measurement error and uncertainty.

Q: emts 8₁ = 19.9 V. 8₂-10.7 V, and 83-5.40 V, and the resistances are each 2.000. What are the (a)…

A:

Q: Sl.no Symbols Name of the components 1. 2. 3. 4.

A: here, the various symbols of the pneumatic circuits are given  which can be useful to make PLC…

Q: |Fill in the table for a correctly wired duplex outlet (U.S. National Electric Code standards for…

A: The answer to the above problem is given below.

Q: What is sub station

A: A power station is to provide electricity to a huge number of people. Different customer’s power…

Q: & Prove That %3D

A: Resonance Resonance is the condition when the voltage across a circuit becomes in phase with the…

Q: 1. WRITE THE CKT. DIAGRAM OE FOUR BASIC TYPES OF SERIES CKT.

A: Series circuit A Series Circuit occurs when two or more loads are linked in series. If one load or…

Q: With neat diagram explain the construction and working of CRO.

A:

Q: In static characteristics, is defined as the difference between the true value applied to a…

A: in static characteristics, Accuracy is defined as the difference between the true value applied to a…

Q: What is the percentage of carbon residue? What is the importance of carbon residue?

A: 1) The carbon Residue value of fuel depends on the refinery processes employed in its manufacture.…

Q: 1.verify (Kc) and (KUL)) ?

A:

Q: Q2. What are the major carriers in the depletion region? Explain.

A: Here i have described it.

Q: Test 2: Modified true or false:Shade letter A if the first statement is True, Shade Letter B if the…

A: The given statements are as follows, 1. The passing general average rating shall be seventy percent…

Q: Difference in the digital and the analog systems

A: Both digital and the analog systems are used to transmit and received information (or signals). The…

Q: tronic components definitions and si units and color coding

A: Electronic components : There are mainly two type of Electronic components one is active Electronic…

Q: Label the parts of Tubular Steel Poles

A: Steel tabular poles are not commonly used poles these poles are used when there is need of low cost…

Q: What is UHV and EHV?

A: EHV stands for Extra High Voltage transmission line whereas UHV stands for Ultra High Voltage…

Q: A transistor is used as a switch and the waveforms are shown below. The parameters are given as…

A: Given  Transistor as switch and waveforms as shown  Vcc=200 vVCE(sat)=1 vICS=100 AICEO=1 mArise time…

Q: Briefly describe how a distance can be measured by the method of phase comparison

A: From the method of phase comparison, the distance is measured indirectly by determining the number…

Q: Please show the work in between the rearranged formula and the answer

A: Given: Calculate the S/N in dB if the passband circuit is 48kHz to 64kHz and the maximum bit rate is…

Q: Q1. Convert following numbers in given radix system: a. (173)10 into hexadecimal b. (2E3)16 into…

A:

Q: Experiment Title SIGNAL GENERATORS

A: WE have to discuss signal generator, The sine wave generator represents the largest single category…

Q: Write a paragraph about your hopes and ambitions. In about 100 words

A: Hope and ambitions are the most important part of any human which can include the happiness of…

Q: Discuss the operation of a multi-meter

A: Solution :    In the above question they are interested to know the operation of a multimeter.   As…

Q: Given: a = 8, 6 = 500 Find I1 in rectangular form. [a + j3 -j2 8- j5 -j2 %3D I2

A:

Q: 3. Explain the successive approximation type ADC with neat schematic diagram.

A: Successive approximation ADC: The successive approximation ADC is a type of converter that converts…

Q: Use block diagram formula

A:

Q: 3) What is the dropout ratio? What is the advantages of dropout ratio in power systems. (min 1 page)

A: A pick-up and drop-out ratio terms related to protective relays. The pickup current of a circuit…

Q: What is national electricity grid

A: In this case, we need to explain what is national electricity grid.

Q: A company is producing a certain type of circuit breaker. The fixed cost is (450 000$), and the…

A: Given data, Fixed cost of CB, FC=$450000 Variable cost, VC=$33/unit Breakeven at 37500 units.

Q: Give the title proposal about renewable energy atleast 5 title Bachelor electrical engineering

A: Renewable Energy:- Renewable energy is produced using resources found in nature that are not…

Q: 9Vpk pk Vin Vout 1.25 2.25 3.75 4.50 -1.25 -2.25 -3.75 -4.50

A: We need to find out output voltage for given input values in clamper circuit .

Q: What Is a function of a capacity

A:

Q: 10. Describe with one sentence what the shape functions in FEM are.

A:

KVL and KCL

KVL stands for Kirchhoff voltage law. KVL states that the total voltage drops around the loop in any closed electric circuit is equal to the sum of total voltage drop in the same closed loop.

Sign Convention

Science and technology incorporate some ideas and techniques of their own to understand a system skilfully and easily. These techniques are called conventions. For example: Sign conventions of mirrors are used to understand the phenomenon of reflection and refraction in an easier way.