01. Each of the members of the truss loaded as shown is an L 50 x 40 x 5 of A36 steel. For member BC, calculate the following: a. Stress in the member b. Strain in the member 160 kN 120 kN 80 kN 120 kN 4 m 80 kN 5 m 5 m B 2 @ 5 m = 10 m 3 @ 5 m= 15 m %3D 4.

01. Each of the members of the truss loaded as shown is an L 50 x 40 x 5 of A36 steel. For member BC, calculate the following: a. Stress in the member b. Strain in the member 160 kN 120 kN 80 kN 120 kN 4 m 80 kN 5 m 5 m B 2 @ 5 m = 10 m 3 @ 5 m= 15 m %3D 4.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the stresses in each bar and the bond reactions.
A2
Rigid bar ABCD is supported by a pin connection at A and by two axial bars (1) and (2). Bar (1) is a 30-in.-long bronze [E = 15900 ksi a = 9.4x 10-6/°F] bar with a cross-sectional area of 1.00 in.?. Bar (2) is a 48-in-long aluminum alloy [E = 9200 ksi, a = 12.6 x 10-6/°F] bar with a cross-sectional area of 2.50 in.?. Both bars are unstressed before the load Pis applied. Assume L4=30 in., L2=48 in., a-32 in., b=44 in., and c=14 in. If a concentrated load of P = 29 kips is applied to the rigid bar at Dand the temperature is decreased by 120°F, determine: (a) the normal stresses in bars (1) and (2). (b) the normal strains in bars (1) and (2). (c) the deflection of the rigid bar at point D. (2) L2 A B D L1 (1) b
The critical bending compressive stress in the extreme fibre of a structural steel section is 1000 MPa. It is given that the yield strength of the steel is 250 MPa, width of flange is 250 mm and thickness of flange is 15 mm. As per the provisions of IS: 800 -2007, the non-dimensional slenderness ratio of the steel cross-section is (a) 0.25 (c) 2.00 (b) 0.75 (d) 0.50
The pin-connected structure consists of a rigid beam ABCD and two supporting bars. Bar (1) is an aluminum alloy [E = 79 GPa] with a cross-sectional area of A₁ = 700 mm². Bar (2) is a bronze alloy [E = 106 GPa] with a cross-sectional area of A₂ = 480 mm². Assume L₁=1.8 m, L₂=2.1 m, a=0.5 m, b=1.6 m, and c=0.8 m. All bars are unstressed before the load P is applied; however, there is a 3.4-mm clearance in the pin connection at A. If a load of P = 53 kN is applied at B, determine: (a) the normal stresses 01, 02, in both bars (1) and (2). (b) the normal strains 1, 2, in bars (1) and (2). (c) determine the downward deflection VA of point A on the rigid bar. (1) A Answers: (a) σ₁ = (b) 1 (c) VA = i a L₁ B b (2) L2 MPa, 0₁ = με, €2 = mm. i i D MPa. με.
The pin-connected structure shown consists of a rigid bar ABCD and two axial members. Bar (1) is steel [E = 200 GPa; a = 11.7x 10-6/°C], with a cross-sectional area of A1 = 370 mm2. Bar (2) is an aluminum alloy [E = 70 GPa; a = 22.5 x 10-6/°C], with a cross- sectional area of A2 = 380 mm?. The bars are unstressed when the structure is assembled. Assume a=360O mm, b=620 mm, c=730 mm, P=20 kN, and L=890 mm. After a concentrated load of P = 20 kN is applied and the temperature is increased by 35°C, determine (a) the normal stresses in bars (1) and (2). (b) the deflection of point D on the rigid bar. A (1) B (2)
The aluminum rod AB (Gal = 27 GPa) is bonded to %3D the brass rod BD (Gpr = 39 GPa). The portion CD of %3D the brass rod is hollow and has an inner diameter of 40 mm. If the allowable shear stresses for the aluminum and brass are 90 MPa and 70 MPa, respectively, and the allowable angle of twist of the free end A is 6 degrees, determine the maximum permissible value of T. 60 mm 2T 36 mm T 250 mm 375 mm 400 mm
H.W 3 Two aluminum alloy plates (2) are attached to the sides of a wooden beam (1) as shown in Figure 3. mensions of the composite cross section are b1 = 80 mm, d¡ = 240 mm, b2 = 10 mm, d2 = b2 The di- |di 120 mm, and a = 60 mm. Deter- (2) (2) %3D mine the maximum bending (1) a stresses produced in both the wooden beam and the aluminum b1 plates if a bending moment FIGURE 3 +6,000 N m is applied M2 %3D about the z axis. Assume that Ej = 12.5 GPa and E2 = 70 GPa.
Compound axial member ABC has a uniform diameter of d = 1.25 in. • Segment (1) is an aluminum [E1 = 10000 ksi] alloy. The length of segment (1) is L1 = 100 in. • Segment (2) is a copper [E2 = 17000 ksi] alloy. The length of segment (2) is L2 = 140 in. When axial force Pis applied, a strain gage attached to copper segment (2) measures a normal strain of ɛ2 = 2300 uin./in. in the longitudinal direction. What is the total elongation of member ABC? L2 (1) Aluminum B (2) Copper Answer: in, AL = i
Rigid bar ABCD is supported by a pin connection at A and by two axial bars (1) and (2). Bar (1) is a 32-in.-long bronze [E = 13700 ksi] bar with a cross-sectional area of 1.29 in.2. Bar (2) is a 48-in.-long aluminum alloy [E = 10300 ksi] bar with a cross-sectional area of 2.19 in.2. Assume L1=32 in., L2=48 in., a=25 in., b=57 in., and c=15 in. Both bars are unstressed before the load P is applied. If a concentrated load of P = 26 kips is applied to the rigid bar at D, determine:(a) the normal stresses σ1, σ2 in bars (1) and (2).(b) the downward deflection vD of point D on the rigid bar.
H1
H.W 3 Two aluminum alloy plates (2) are attached to the sides of a wooden beam (1) as shown in Figure 3. mensions of the composite cross section are bj = 80 mm, d1 = dz 240 mm, b2 = 10 mm, d2 = The di- di %3D %3D 120 mm, and a = 60 mm. Deter- (2) (2) (1) mine the maximum bending stresses produced in both the wooden beam and the aluminum b1 plates if a bending moment M = +6,000 N m is applied about the z axis. Assume that E = 12.5 GPa and E2 = 70 GPa. FIGURE 3 %3D