part C plz The 2014-T6 aluminum strut is fixed between thetwo walls at A and B. It has a 2 in. by2 in. square cross section, and it is subjected tothe torsional loading shown where Ti 18 lb-ftand T₂ =40 lb-ft. (Eigure 1)Figure1 of 1Determine the reactions at the fixed support BExpress your answer to three significant figures and include appropriate uniTh25.3 lb-ftCorrectPart CPrevious AnswersWhat is the angle of twist at C?Express your answer to three significant figures and include appropriate units.0.008μÅProvide FeedbackradSubmit Previous Answers Request AnswerX Incorrect: Try Again; 4 attempts remaining

T1 = 18 lb-ftT2 = 40 lb-ftAC = CD = BD = 2 ft

Answered: 00 0.008 rad

Engineering

Mechanical Engineering

00 0.008 rad

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.5.30P: A mountain bike rider going uphill applies a force P = 65 N to each end of the handlebars AB CD,...

See similar textbooks

Related questions

Q: Liquid cooling system is advantageous because: Select one: a. It requires many components (pump,…

A: Option b is correct Because liquid have high conductivity than air so it will be remove heat at…

Q: The velocity of a particle moving in the x-y plane is given by (7.82i +3.51j) m/s at time t = 3.15…

A: Given:To find:

Q: Define the sideslip angle at the centre of gravity of a car. Then show that v+raj B11 = u-rt1/2…

A: Sideslip angle:The difference between the two directions of a vehicle moving and the direction the…

Q: The following box beam is constructed from four boards that are fastened together using nails. A…

Q: A 6-x 10-in. timber beam has been strengthened by bolting two - x 2-in. steel straps to it as shown…

A: Given: Modulus of elasticity of the wood: →E1=1.5×106 psi Modulus of elasticity of the steel:…

Q: Determine the absolute value of the first moment of the area (in mm) about the indicated x-axis in…

Q: Part C Also, a turbine can be used before the pipeline exit to produce electricity. If the used…

Q: In the truss structure shown below, all members except the central one are perfectly rigid. The…

A: GivenE=1 GPa=109 Pam=1 kgA=1cm2=10-4 m2L=30cm=30×10-2 m∆L=0.01 cm=0.01×10-2 mAskedT=?FormulaG=TA∆LL

Q: A light elastic string has natural length a and modulus of elasticity 12mg. One end of the string is…

Q: The deceleration of the truck The stopping distances Time needed to stop the truck 2

A: Given: u= 90 km/h Braking force=6900 N m=2300 kg v=0 To determine: Deceleration of the truck Time to…

Q: Part B Taking in your consideration the head losses accumulated by the fluid when flowing in the…

Q: Consider the beam shown in (Eigure 1). Take E = 29(10³) ksi, I = 160 in². gure 2k/f -10 ft -10 ft…

A: For the beam E=29000 ksi, I=160 in4.

Q: (a) Determine the reactions at A and E if P = 920 N. The reactions are positive if to the right or…

Q: A piezoelectric type accelerometer has a sensitivity of 100 mV/g. The transducer is subjected to a…

Q: Find the centroid of the shaded plane with respect to reference axis in the figure shown below. 2 m…

A: Answer: The centroid of the shaded area: (X, Y) = (3.1110 m, 1.9496 m)

Q: The rod has a diameter of 40 mm. It is subjected to the force system F₂ = 1300 N, Fy = 600 N, F₂ =…

A: The rod diameter d =40 mm = 0.04mThe force systemFx= 1300NFy= 600NFz= 900NFindThe Normal stress act…

Q: (b) A block weighing 2000 N is on a rough inclined plane that makes angle of 15° with horizontal.…

A: Given:W=2000 Nθ=15°F=800 N

Q: Bending Stress A cantilever beam of length 1.1 m carries a uniformly distributed load w, as shown in…

A: Length of the beam (L): 1 mUniformly distributed load (W): Given but not specified, please provide…

Q: The solution set of the equation x 3 7| 2 x 2 = 0 is: 7 6 O (2. 3, 7) O 2.7. (2, 7, -9) O (-2. 3, 7)…

A: Givenx372x276x=0

Q: Figure B2 shows a crank driven assembly that comprises three connected slender bars (AB, BC and CDE)…

A: Given: AB=0.3 mBC=0.5 mCD=0.3 mDE=0.6 mθ˙=10 rad/s

Q: A horizontally positioned door weighing 1200 N is held in place by hinges centered at points A and B…

A: Given: The weight of door, W = -1200k

Q: A flat steel bar, 30 mm wide by 2 mm thick and 1.6 m long, is bent by couples applied at the ends so…

Q: istants Periodic Table An ideal gas is confined within a thermally isolated cylinder. It consists of…

A: Yes is the correct answer.

Q: |Umax u = u(r) s this flow

A: U=Umax(1-(2yh)2] UMAX=25 cm/s=0.25 m/sviscocity μ=3.5 cp=3.5 x 10-3 N-s/m2area of lower plate ,…

Q: 5. The semicircular gate is hinged at point A. What is the necessary force P needed to hold the gate…

A: The required force P. Given: The radius of the gate is R=15-8=7 ft. FBD: The free-body diagram of…

Q: A schematic of a combined refrigeration cycle and a portion of a steam power cycle is shown in the…

A: m_3 = 3[kg/s] P[1] = 5000[kPa]T[1] = 350[C] P[2] = 2000[kPa]T[2] = 250[C] P[3] = 200[kPa]x[3] =…

Q: At the beginning of the compression process of an air standard Otto cycle, p1= 1 bar, T1= 300 K. The…

A: Given, P1=1barT1=300KT3=2250KCompression ratio,r=9.8Engine displacement, Vd=2.7L=2.7×10-3m3/s T-S…

Q: 3. You have engaged in open discussion in which you have to evaluate the conditions needed for an…

A: As per Demand of yours to do Part 3 So as below is Drawing of Epicyclic Gear train

Q: Problem 1 A jet of water discharges into an open tank, and water leaves the tank through an orifice…

Q: Water is the working fluid in an ideal Rankine cycle. Steam enters the turbine at 1400 lb/in² and…

A: To find: (a) The mass flow rate of steam. (b) The rate of heat transfer in steam generator. (c) The…

Q: A reservoir supplies water as shown in Fig. 1. The pipe system consists of 6 m of pipe and two 90°…

Q: Explain the differences between pumps, compressors, and turbines.

A: In the given question, it is asked about the differences between pump, compressor and turbine.

Q: 2. Give the procedures in finding the friction factor f using the Moody Chart. Provide

A: Given data Procedure to find the friction factor using moody chart.

Q: The net power imput

Q: The torsional assembly shown in Figure 1 consists of solid 2.50-in.-diameter aluminum [G = 4,000…

Question

part C plz

The 2014-T6 aluminum strut is fixed between the
two walls at A and B. It has a 2 in. by
2 in. square cross section, and it is subjected to
the torsional loading shown where Ti 18 lb-ft
and T₂ =40 lb-ft. (Eigure 1)
Figure
1 of 1
Determine the reactions at the fixed support B
Express your answer to three significant figures and include appropriate uni
Th
25.3 lb-ft
Correct
Part C
Previous Answers
What is the angle of twist at C?
Express your answer to three significant figures and include appropriate units.
0.008
μÅ
Provide Feedback
rad
Submit Previous Answers Request Answer
X Incorrect: Try Again; 4 attempts remaining

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Write down give data

VIEW

Step 2: Calculation of TA andd TB

VIEW

Step 3: calculation of angle of twist

VIEW

Solution

VIEW

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Clear my choice Let's consider a rod having a solid circular cross-section with diameter of 4 mm and it is made of a material having a Young's modulus E= 200 Gpa and a Poisson's ratio of 0.3. If a tensile force Fis subjected to that rod cross-section, the diameter becomes 3.995 mm. determine the applied force F. Select one: O F= 5236 N OF=15708N O F= 13090 N OF=10472 N OF=4189 N O F=6283 N Clear my choice Finish attempt NEXT ACTIVITY MENG360 Test -Spring 2020-2021 Jup to
Please draw the free body diagram. And the answer must be correct (Handwritten recommended)
Please help me solve these questions for part a and part B they’re both linked use image below Circle final answer for both of them
Clear my choice Let's consider a rod having a solid circular cross-section with diameter of 6 mm and it is made of a material having a Young's modulus E = 120 Gpa and a Poisson's ratio of 0.33. If a tensile force F is subjected to that rod cross-section, the diameter becomes 5.998 mm. determine the applied force F. Select one: O F= 5712 N O F= 2285 N O F= 8568 N O F= 2856 N O F= 3427 N O F=7140 N Finish attempt..
The rigid bar ABC is supported by pin at A and aluminum wire BD, is horizontal before the Load P is applied. Find the vertical displacement of point C caused by the load P=35KN. Where E of aluminum equals 70GPA and the area of the wire is 200mm^2 -Draw and label the diagram correctly, No diagram in the solution will be marked wrong. -Shortcut solution will be marked wrong.- Direction of the assumption of the equilibrium equation must be shown, no direction will be marked wrong.
Let's consider a rod having a solid circular cross-section with diameter of 6 mm and it is made of a material having a Young's modulus E = 200 Gpa and a Poisson's ratio of 0.3. If a tensile force F is subjected to that rod cross-section, the diameter becomes 5.995 mm. determine the applied force F. Select one: O F=15708N O F= 10472 N O F=5236 N O F= 13090 N O F=6283 N O F=4189 N
Figure 2: Given the below determine the bar force at BD. (Answer in whole number, indicate the answer in kN. just input the value, do this for all the questions on Figure 2) Note: if the member is in compression, write a negative symbol before it, ex: 12kn in compression is answer:-12
The true option
Prior to the application of the P = 120 kip load, the gap between C and the rigid wall at D was as depicted as below. Determine the support reaction at D (in kip) after force P has been applied. The assembly is made of solid cylinders: AB is Stainless 304 steel alloy, and BC is 6061-T6 aluminum alloy.
Show all working explaining detailly each step.
Figure 2: Given the below determine the bar force at AB. (Answer in whole number, indicate the answer in kN. just input the value, do this for all the questions on Figure 2) Note: if the member is in compression, write a negative symbol before it, ex: 12kn in compression is answer:-12
The assembly consists of two-rod brass C83400 copper alloy rods AB and CD of diameter 30 mm, a stainless 304 steel alloy rods EF and FG of diameter 40 mm, and a rigid cap H as shown in Figure 2. Neglect the size of the collar at F. Assume that the modulus of elasticity Esteel = 200 GPa and Ebrass = 101 GPa. If the force, P = 5 kN, (a) Sketch the free body diagram and calculate the internal forces acting in each section of the rod. (b) Determine the average normal stress developed in rods FG, EF and AB. (c) Determine the average normal strain in the rod of AB.(d) If the horizontal displacement of end G of rod FG is 0.6 mm, determine the new magnitude of P.