0.9 m 0.7 m 0.5 m | 120 mm TA = 6 kN•m B Тв — 14 kN-m Tc = 26 kN•m Tp = 6 kN-m

Q: (5) When the bar subjected to torque, the maximum shear stress occur at.. O A. External surface of…

A: When a bar is subjected to the torque, the shear stress will be produced in the bar.

Q: Knowing that each of the shafts AB, BC, and CD consists of a solid circular rod. Knowing that both…

A: we are going to apply the Torsion equation over the shaft.

Q: A solid steel shaft will not twist through more than 3 degrees in a 6-m length when subjected to a…

A: Given data: The angle of twist, θ=3°. The length of shaft, L=6 m. The applied torque, T=12 kN·m.…

Q: Link AB, of width b =50 mm and thickness t = 6 mm, is used to support the end of a horizontal beam.…

A: Given Width = 50 mm Thickness = 6 mm Allowable normal stress = 2140 MPa Allowable shear shear stress…

Q: E' 3. For the 3-in.-diameter solid cylinder and loading shown, T = 40 kip-in., determine: (a) the…

A:

Q: A composite beam is made by attaching the timber and steel portions shown with bolts of 12-mm…

A:

Q: Q2) The aluminum rod BC (G-26 GPa) is bonded to the brass rod AB (G-39 GPa). Knowing that Birass…

A: For solution refer below images.

Q: Link AB, of width b = 2 in. and thicknesst = ¼ in., is used to support the end of a horizontal beam.…

A: Handwriting.jpg

Q: The driveshaft of an automobile is being designed to transmit 172 hp at 2950 rpm. Determine the…

A:

Q: Link AB, of width b = 50 mm and thickness,t = 6 mm, is used to support the end of a horizontal beam.…

A: Given data: b=50 mmt=6 mmσ=2140 MPaτ=80 MPa Need to determine the diameter of the pins and average…

Q: 2. a. Knowing that the allowable shearing stress is 8ksi, for the stepped shaft shown, determine the…

A: Step 1: Step 2: Step 3: Step 4:

Q: 3. Gear B supplies 20 KW of power, while gears A, Cand D withdraw 6 kW, 4 kW and 10 kW,…

A: Answer: The required minimum diameter of the shaft is 24.5 mm.

Q: The solid shaft shown is formed of a brass for which the allowable shearing stress is 55 MPa.…

A: if you have any doubts please comment

Q: he ends A and D of the two solid shafts AB and CD are fixed, while the ends B and C are connected to…

A: Given:dAB=60 mmrB=100 mmrc=40 mmdCD=45 mmζallow=50 MPa

Q: 4. The solid cylinders AB and BC are bonded together at B and are attached to fixed supports at A…

A:

Q: 5. The torques shown are exerted on pulleys A and B. The diameter of the shaft AB is dAB = 50mm…

A: To transmit energy by rotation it is necessary to apply a turning force. in the case of a shaft if…

Q: The hollow steel shaft has a diameter of 65 mm and thickness of 5mm, is subjected to a torque and…

A: Given that, Outer diameter, Do=65 mm,Thickness of hollow shaft, t=5 mm,Force, F=3 kN,Eccentricity,…

Q: The torque T causes a rotation of 2° at end B of the stainless-steel bar shown. Knowing that b = 20…

A: The rotation of the bar is .The distances are given as-The length of the bar is .The shear modulus…

Q: For the state of stress shown, determine the maximum shearing stress when (a) ơ, = 0, (b) ơz = 60…

A: σavg=1230+100 =6512σx-σy=1230-100=-35

Q: The design of a machine element calls for a 40-mm-outer diameter shaft to transmit 45 kW. (a) If the…

A:

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.