0.6 m 0,4 m. 450 N -y 0.6 m 0.6 m Prob. F5-10

Q: Determine the reactions to the structure 5 ft 8888 5 ft 5 ft 15P 5P B

A: Given data:- Forces applied=8P (downward),15P (downward) and 5P (upward) Length of the beam=15 ft To…

Q: Q/ Determine the reactions at the supports (A and c).

A:

Q: How about this part :"Determine the x and y components of reaction the pin C exerts on member EDC…

A: F1 = 8 KN

Q: Calculate the reactions on the supports A and B 8000 N/m A B 4.2m

A:

Q: loh: proced ● Determine reactions at A and C A 2 m MB 1m -C Rc

A:

Q: Determine the reactions at A, B, C, and D on the cylinders. Assuming smooth contact surfaces.W1=…

A:

Q: 2- For the shown structure, draw the free-body diagram and then determine the reactions at A and B.…

A: Ra = 26.67 kN Rbx = 26.67 kNRby = 40 kNExplanation:-Draw first the free body diagram of the…

Q: Determine the magnitude of the roller reaction at E.

A: Given data To determine the support reaction at E

Q: 2. Determine the reactions at 'B' and 'D' 20 kN 6 m 6m 2 m 2m 4 m

A:

Q: Determine the horizontal and vertical components of reaction on the beam caused by the pin at 8 and…

A: To determine the reaction for the given loading.

Q: Determine the Reactions 8 kN 2 kN/m BIC 3m 3m2m-3m- D m

A: According to the given data, all the free-body diagram are drawn below We need to find  Reactions

Q: Solve for the reactions at point A. A 9.33 KN B. 10.33 KN C. 11.33 kN 3m B D E -2 m2 m-2 m--2m--2m-2…

A: Given data: The distance between AB, BC, CD, DE, EF and FG is x = 2 m. The force acting on joint B…

Q: Determine the reactions at A, B, C, and D on the cylinders. Assuming smooth contact surfaces.W1=…

A: GIVEN:

Q: 2) Determine the reactions at A and D. (D is fixed to the soil) (take note of the sign) F1 F2 H. F3…

A: Given: F2(KN)=20 F1(KN)=5 F3(KN)=10 L1(m)=4 H(m)=-5

Q: Q/. Determine the normal reaction at the roller A and horizontal and vertical components at pin B…

A:

Q: 37N 367N R=1.05 426N B 426N The two identical sphmes haring oqual weights of 367N is placed on top…

A: There are two types of forces that are acting on a circular surface. One type of force is Radial…

Q: Determine the reactions at the Smooth contact points A,B and C 250 N 30 30 0.15 m 0.2 m

A: Apply Static equilibrium to solve this problem

Q: Determine the reaction components at the hinge support at Band the roller support at A due to the…

A:

Q: Determine the magnitude of the roller reaction at E. 400 kN

A: Given data To determine the reaction at the roller support.

Q: Cable Hinge

A:

Q: Determine the reactions to the structure 4P 60 FT. 15 FT. B

A:

Q: Question 1 Neglecting the weights of the bar and the pulley and assuming the weight of the ball B to…

A:

Q: QI. Determine the normal reaction at the roller A and horizontal and vertical components at pin B…

A:

Q: 30 kip 5 kip/ft

A: To determine the support reaction at B we will first draw the free body diagram.

Q: Determine the reactions at the supports. 400 N/m - 3m- A = 750 N By = 600 N Bx = 450 N

A:

Q: The shaft is supported by three smooth journal bearings at A, B, and C. Determine the components of…

A: Given : system consists of forces applied in different directions supported by journal bearings.Find…

Q: For the structure loaded as shown in the figure, determine the reaction at A

A:

Q: 1oft 一T4- トガルー

A:

Q: Determine support reaction

A:

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.