0.5 in. B 6 in. 2 in. 6 in.. 0.5 in. 2 in. 0.5 in. 0.5 in.

Q: If the wide-flange beam is subjected to a shear of V = 20 kN, determine the maximum shear stress in…

A: From the half section above neutral axis:

Q: Draw the shear and Moment diagram 5,KN 2 kN/m 10m R₂

A:

Q: Determine the location of shear center of the following cross section.

A: Given:

Q: The H-beam is subjected to a shear of V=60 kN. determinate the flow at point A

A: The shear force is

Q: If the T-beam is subjected to a veritcal Shear of kips, determine the maximum horizontal shear…

A:

Q: If the wide-flange beam is subjected to a shear of V = 30 kN, determine the maximum shear stress in…

A: The diagram of I-section is given as, The maximum shear stress is written as, The value of Q is…

Q: The wood has an allowable shear stress of Tallow = 6 MPa. Determine the maximum shear force Vthat…

A:

Q: Determine the axial forces, shears, and bending moments at points A and B of the structure shown.

A: Here Rx=12k cos60oRx=6kFor equilibrium condition,∑Fy=0Ry+12k sin60o-8k=0Ry+2.39k=0Ry=-2.39kMoment ,…

Q: 12-1. If the wide-flange beam is subjected to a shear of V = 20 kN, determine the shear stress on…

A: Draw the load-bearing section of the beam.

Q: If the beam is subjected to a shear of V = 15 kN, determine the web’s shear stress at A and B.…

A:

Q: Q6) The channel is subjected to a shear of V= 60 kN. Determine the maximum shear flow in the…

A:

Q: Determine the shear centre of the circular arc section as shown in fig. 9-24. 0 k e 1cm Fig. 9-24…

A: Find, Shear center (e).

Q: The aluminum strut is 10 mm thick and has the cross section shown. If it is subjected to a shear of…

A:

Q: The beam is used to support a dead load of 0.6 k/ft, a live load of 2 k/ft and a concentrated live…

A: Given data are, Live load= 2 k/ft Dead load= 0.6 k/ft Generated live load= 8 k Now, draw the FBD of…

Q: Determine the resultant internal normal force, shear force, and bending moment at point C in the…

A: Draw the free-body diagram of the section AB. Draw the free-body diagram of the section BC.

Q: 15 kN/m 2 m - 2 m 0.5 m'

A: RA is the reaction force at left support and RB is the reaction force at right support. ∑FV =0  RA +…

Q: 12-31. The beam has a square cross section and is made of wood having an allowable shear stress of…

A: given data as per the question Allowable shear stress = 10 Mpa value of shear subjected = 70 KN…

Q: Three plates are welded together to form the section shown.  Dimensions of the cross section are b =…

A:

Q: 2 KN/m 2 KN/m 3 m 3 m R R2

A: A beam is defined as a structural member subjected to transverse shear load during its…

Q: W A C В 1 /2'

A:

Q: A beam is constructed from three boards bolted together as shown. Determine the shear force in each…

A: Consider the diagram shown below for the cross-section of the beam.

Q: 7-46. The beam is subjected to a shear of V = 800 N. Determine the average shear stress developed in…

A:

Q: If the wide-flange beam is subjected to a shear of V = 20 kN, determine the shear stress on the web…

A: The moment of inertia about the neutral axis: I = 0.2×0.34312-0.18×0.3312I = 2.50×10-4 m4Section…

Q: If the wide-flange beam is subjected to a shear of V = 30 kN, determine the shear force resisted by…

A: Average shear stress in a beam is given by, τavg = VQI t   Where V = Transverse Load applied on…

Q: 12-3. If the wide-flange beam is subjected to a shear of V= 20 kN, determine the shear force…

A: For the given section of a beam, shear force actin on this section is, V=20 kN Since its a…

Q: Draw the shear and Moment diagram AF RI fzm 10 kN/m i B 2m 5KN Im Lim R₂

A:

Q: per the attached figure:   a shear force of V=340 kN is applied to the box girder. determine the…

A: Consider the figure showing the cross-section of the structure (box). Here, the neutral axis is N.

Q: The beam is subjected to a shear of V = 850 N  Determine the average shear stress developed in the…

A:

Q: The channel beam with b= 300 mm, h=150 mm, and constant thickness of t=15 mm is subjected to a shear…

A: