0.4 m 60 m 15 m 40 m 55 m a) Determine the ULS uniformly distributed load 'S' (in kPa), snow load, needed to design the lower roof. Remember to check both the basic snow and the rain load. The building is 'normal importance in downtown Suffield with a flat roof plan of 60 m by 55 m Snow load (S) - N 4 kPa. b) Determine the ULS snow drift if that roof sits below a second building with a higher roof (see sketch). Calculate the Case I drift only. Draw a sketch to summarize your calculations. Drift peak- A kPa.

0.4 m 60 m 15 m 40 m 55 m a) Determine the ULS uniformly distributed load 'S' (in kPa), snow load, needed to design the lower roof. Remember to check both the basic snow and the rain load. The building is 'normal importance in downtown Suffield with a flat roof plan of 60 m by 55 m Snow load (S) - N 4 kPa. b) Determine the ULS snow drift if that roof sits below a second building with a higher roof (see sketch). Calculate the Case I drift only. Draw a sketch to summarize your calculations. Drift peak- A kPa.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The lateral force-resisting system of the four-storey special moment frame building shown below has a 7.50m setback at the 3rd and 4th levels. TYROA EANON No Irregularity In-plane Discontinuity Weak Story Overtical geometric irregularity
Designing and detailing of singly reinforced simply supported beam - BS Code - Manual (BS 8110-1:1997)
An essential 5-story facility structure is conceptualized with an intermediate reinforced concrete moment frame. It is located on a site in zone 4 with a soil profile type Sp. The site is situated 13 kilometers from a potential seismic source type A. The story heights are 5.4 m at the ground floor and 4.3 m for the the 2nd and 5th floors. The story dead loads are 7600 kN from the bottom up. The plan dimensions are 55 m by 37m. The moment frames consist of two four bay frames in the transverse direction and two seven bay frames in the longitudinal direction. Determine the following: 25) Overturning moment at 2nd floor O 99,284 kN-m O 200,069 kN-m O 150,123 kN-m O 109,265 kN-m
(a) empt The detached servant room of a quarter is having internal size of 3.0m x4.50m. It is to be covered by a roof of RCC. The dead load on roof 4.5 kN/m² and the live load is 1.50 kN/m² Design the slab by I.S. Code method. Assume grade of concrete as M25 and grade of Steel as Fe415.
Design a simple supported slab for a 4 m (out-to-out) wide and 20 m (out-to-out) long waiting shed. The longitudinal beam has a size of 200 mm by 400mm. The slab carries the following superimposed dead loads: waterproofing of 0.02 kPa, ceiling load of 0.1 kPa and mechanical-electrical utilities 0.2 kPa. The superimposed live load to be applied is 1.4 kPa. The slab will be reinforced with 12mmΦ main reinforcements and 10mmΦ temperature reinforcements. The concrete has a full strength of 20.7 MPa and the reinforcement’s yield strength has a strength of 345 MPa.
An five-Storey Hotel is to be designed using a two-way slab supported by 400mm x 650mm monolithic beams on the beam-column lines, having a slab dimensions of 5.85m x 7.25m center-to-center spacing. A supper imposed Dead load of 4.55KPa for partition and Live loading of 15.68KPa is specified. Find the required slab thickness, using the steel ratio of approximately 0.0151 maximum, and design the reinforcement for a typical exterior-edge panel (two-sides without continuous slab). Detail the reinforcement, showing size, spacing, and length of rebars. All straight bars will be used. Material strengths will be f’c= 21.5MPa and fy =275MPa. Use combination: 1.2 DL + 1.6 LL. Use the moment coefficient method.