= 0.00986 in. H2O-min-ft/ 6.5 For Ke = 0.577 in. H90-min/ft and K, gr, design a reverse-air baghouse to filter 20,000 cfm of air with 2,5 gr/ft of flour, Assume a cleaning time of 3.0 minutes and a filtration time of 60 minutes. In your design, specify the number of compartments, the filtering velocity, the cloth area per com- partment, and the total number of bags required if each bag is 10 ft long and 1 ft in diameter. Also, specify the maximum pressure drop that will be experienced đuring the run.

= 0.00986 in. H2O-min-ft/ 6.5 For Ke = 0.577 in. H90-min/ft and K, gr, design a reverse-air baghouse to filter 20,000 cfm of air with 2,5 gr/ft of flour, Assume a cleaning time of 3.0 minutes and a filtration time of 60 minutes. In your design, specify the number of compartments, the filtering velocity, the cloth area per com- partment, and the total number of bags required if each bag is 10 ft long and 1 ft in diameter. Also, specify the maximum pressure drop that will be experienced đuring the run.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

2. Sketch: a. 3 stages of single crystal stress-strain curve under uniaxial stress b. Frank-Reed mechanism for dislocation multiplication.
The flow stress for an alloy is 115 Mpa when its dislocation density is 10^6 cm^-2 and 207 Mpa when its dislocation density is 10^8 cm^-2. When the flow stress is 359 Mpa, Find the dislocation density.
(c) Sketch the hysteresis loop of the B-H curve for a ferromagnetic material with proper labels at room temperature. (d) Calculate the electrical conductivity of a 6.0 mm diameter cylindrical silicon specimen of 60 mm long in which a current of 0.5 A passes in an axial direction. A voltage of 12.5 V is measured across two probes that are separated by 40 mm. i. Compute the electrical conductivity of the specimen. ii. Compute the resistance over the entire 60 mm of the specimen using the data in (i).
2 . Write the slip systems of the metals with crystal structures of BCC, FCC and HCP. Calculate the total number of slip systems for each case. Which among the BCC, FCC and HCP is the most ductile and why?
Compute the planar density value for (1,-1,1) plane of BCC iron (Fe). Zfe=26Rfe=0.126nmAfe=55.845g/mol
Compare the dependencies of Elastic Modulus andTensile Strengthon chemical composition, atomic bonding and microstructure in solids.
One slip system for the BCC crystal structure is {110} . Sketch this plane along with the BCC atoms and identify two different slip directions within this plane.
Explain why BCC (body-centered cubic) materials generally have higher mechanical strength values than FCC (face-centered cubic) materials in terms of (a) slip systems and (b) extended dislocations.
Consider a single crystal of some hypothetical metal that has the BCC crystal structure and is oriented such that a tensile stress is applied along a [2 2 1] direction. If slip occurs on a (2 1 1) plane and in a [-1 1 1] direction, compute the stress at which the crystal yields if its critical resolved shear stress is 2.4 MPa.
It has been found that 'pyrex' cookware made of borosilicate glass does not shatter during baking or cooking around 300°F. However, shattering of cookware made of soda-lime-silicate glass was frequently reported during the years 2012-2013. Find and explain the possible reasons for cookware shattering. Show your calculation. Assume that the cookwares are free of pores, cracks, and scratches. Given: Material/properties Borosilicate Soda-lime-silicate glass glass Thermal expansion coefficient (x106/°C) Elastic modulus (GPa) Failure stress (MPa) 3 9. 62 68 30 30
Calculate the dislocation spacing in a symmetrical tilt boundary (θ = 0.5◦) in a copper crystal.