0 m A different pendulum has length 32 inches and is released from rest when 0 = 5° (theta = 5 degrees). What is the magnitude of the velocity of the bob 1.6 seconds after release? O A. Less than 0.25 ft/s O B. Between 0.25 and 0.5 ft/s OC. Between 0.5 and 1.5 ft/s O D. Between 1.5 and 2.5 ft/s O E. Greater than 2.5 ft/s

0 m A different pendulum has length 32 inches and is released from rest when 0 = 5° (theta = 5 degrees). What is the magnitude of the velocity of the bob 1.6 seconds after release? O A. Less than 0.25 ft/s O B. Between 0.25 and 0.5 ft/s OC. Between 0.5 and 1.5 ft/s O D. Between 1.5 and 2.5 ft/s O E. Greater than 2.5 ft/s

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Can someone explain how to read a mm drum dial micrometer and check my work please?
I need these three parts answered (Multiple Choice). If you can not answer all three parts please leave it for another tutor to answer. Thank you. For the two holes identified as datum D, what is the total size tolerance specified for those holes? (Multiple Choice)a. .002'b. .003'c. .004'd. .006' The two holes identified as datum D have a counterbore on one end. What size toleranceis specified for the counterbore diameter? (Multiple Choice)a. .010″ (±.005″; see title block)b. .020″ (±.010″; see title block)c. .030″ (±.015″; see title block) What letter represents the revision status of this print? (Multiple Choice)ABCD
Solve it quickly please
Pls do stepwise and correct.
PLEASE DO THIS TYPEWRITTEN AND COMPLETE IT, I WILL UPVOTE. IF NOT COMPLETE AND TYPEWRITTEN, NO UPVOTE. THANK YOU
Need help .Please
! Draw a sketch of the above drawing in A3 (or two A4 paper taped together).
A micrometre is a precision measuring instrument, with 50 division on the thimble. Select one: O True O False
None
Draw front and right-side views of the following object with a completed dimensions. Draw in scale 1:1 on A4 sheet. (Problem is taken from "Graphics for Engineers' by Earle) 78 What can we learm from the drawlng ? 1. The dimension note M10x1.5 means that the hole is a threaded hole. R16 O 16, 2 Holes The letter 'M' means that the threads are made by following a metric thread system. The number "10" Is the major dlameter of the hole and the number 1.5 is the pitch of a thread. However, for coarse threads, it is a common practice to omit specifying the pitches. For example, a note M10 means the pitches of the thread is 1.5 mm. In this book, the pitch is specified in order to facilitate drafting. 2. Drawing symbol of a threaded hole is shown below. - Thin Ine (4H pench The ends of this arc does not meet together but approximately 90 degs, apart. Object Ihe (2i pencil .major dlameter pich2 M10x1 5 3. The circular projection surface at a threaded hole that is raised from a cylinder is…
Read each sentence carefully, and then mark as True or False. * a) Cast iron has a carbon content between 1 % and 4 %. b) In the gray cast irons, C is precipitated as graphite flakes. c) In the white cast iron, Fe is precipitated as flakes. d) Cementite is a mixture of two phases, austenite and ledeburite (Fe3C). e) Pearlite is the eutectoid mixture containing 0.80 % C and is formed at 723°C on slow cooling