平0 3 60 21

Q: What about Mohr's circle?

A: In the previous question, Given: The diameter of shaft, d = 20 mm = 0.02 m The maximum bending…

Q: can you do it in polygon

A: Given vectors : A :  2 kph 45°N of E B :  2.8  kph 58°E of S C :  5.1  kph 28°W of S D : 3.2  kph…

Q: Why is 100 at - here?

A: Why is 100 at - here?

Q: . Find the volume of a bronze bushing if it's inside diameter is 1 inch, outside diameter is 1.50…

A:

Q: 18. How far off from the center of the support is the center of the two holes in the bosses of the…

A: 18)    Distance=4.2-0.66                   =3.54 in

Q: Based on the system shown in Figure 1, develop the position equations from your fixed datum lines,…

A:

Q: Part C - Radius of curvature for AB and BC Determine the radius of curvature for AB, PAB, and for…

A:

Q: cker mechanism rocking angle of 70 degrees. What are the lengths of the 4 bars in inches

A: A four-bar crank-rocker mechanism rocking angle of 70 degrees. What are the lengths of the 4 bars in…

Q: State the difference between the eutectic and eutectoid points.

A: Eutectic point: In the iron carbon phase diagram at 2 percentage of carbon is called eutectic point.…

Q: can you make a sketch of the solution

A:

Q: What is the center of gravity in this figure?

A: given; center of gravity on given figure?

Q: Why is it called Mohr's circle?

A: Mohr’s  circle is graphical representation which enables us to visualize the relationships between…

Q: can you answer 1B

A:

Q: What unit is the 0.000931 ?

A: Torsion equation is given by, TJ=τr=GθLwhere,T = torque acting or applied in N-m or N-mmJ = polar…

Q: A hammer is balanced at the point "A", close to the metal part. If this hammer is then cut along the…

A: Consider the diagram shown below for the hammer with the center of masses for each side.

Q: Where did the 0.10472 rad/s come from?

A:

Q: solve parts 4 and 5 please

A: To draw Mohr circle and to show the orientation of the element of maximum in plane shear stress

Q: 1500# 1500# 1500# 1500# 12' K I

A: In this problem, following steps will be taken 1. Determine the reactions at the supports.' 2. Using…

Q: RIS R12 frant sew R32

A: Given 3D model To find Three views

Q: can you Reslove?

A: To solve the problem you have typed in, follow these steps: Analyze the given data:L2 = 6Q2 = 35…

Q: can make it in Solidwork

A: Given Structure To find 3D model

Q: Part B - Analyzing the force-couple system on a bracket For the bracket shown below, Fi = 165 lb, F…

A: As per the guidelines of BARTLEBY we are subjected to solve only one question at a time. please…

Q: how did you find d1 and d2

A: This question is based on the concept of polar radius.

Q: now please answer question 2 and 3 please

A: This question is based on the concept material science. As per the guidelines we are subjected to…

Q: How do you solve parts a,b and c?

A:

Q: Part C - Maximum allowable axial force for fixed-and-free-end support If the cylindrical column is…

A:

Q: Number of links? The value must be a number 8 Number of full joints (J1)? Figure 2 Figure 2

A: Given mechanisms,

Q: If you have a half circle made of steel and the other half of wood, is the center of the circle…

A:

Q: Hello, I need help with the answer of 3.14 from the picture, please.

A:

Q: how do you know where the point 2 is ? or how do you find point 2

A:

Q: Fload/8 Fload/4 ffort = Fload/8

A: According to the details provided in the question, we need to calculate  we need to find all forces…

Q: The Answer is cut off on the right side.

A:

Q: Figure 1 of 1 8 ft 6 ft 6 ft

A:

Q: how can I get the 85 α

A: