=.(t) (1) For the above circuit, given (t) is unknown s R₁ vc (t) ww R₂. C (t) = 7 sin(8t) C=4 F R₁=20 R₂=20 determine the current source is(t) which has the form is(t) = M cos(8t) + N sin(8t) A. Enter only 'M' as your final answer rounded to the nearest single digit decimal place. For example, if you determine is(t) = 15.86 cos(8t) 32.7 sin(8t) A. then just enter 15.9 as your submitted answer.

=.(t) (1) For the above circuit, given (t) is unknown s R₁ vc (t) ww R₂. C (t) = 7 sin(8t) C=4 F R₁=20 R₂=20 determine the current source is(t) which has the form is(t) = M cos(8t) + N sin(8t) A. Enter only 'M' as your final answer rounded to the nearest single digit decimal place. For example, if you determine is(t) = 15.86 cos(8t) 32.7 sin(8t) A. then just enter 15.9 as your submitted answer.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A battery, resistor, capacitor and switch are connected in series to form an RC circuit as shown below. The switch is closed at time t=0 s. Which of the following statements regarding the circuit is correct? Switch S t M R C + 1 O The potential difference across the capacitor is always greater than the potential difference across the resistor O The potential difference across the resistor is always greater than the potential difference across the capacitor. O Once the capacitor is essentially fully charged, there is no appreciable current in the circuit. O The capacitor charges to its maximum value in one time constant and the current is zero at that time. O The potential difference across the resistor and the potential difference across the capacitor are always equal.
At what time is necessary for a current on a series RL dc circuit to reach 83.5 % of the final steady state value if the time constant is 10 millisecond Assume that at t=0 , i (0 ) = 0.?
solve the question attached using nodal equation
Please please answer this question for me in 20 min and I will be grateful to you thank you in advance
A 400 Hz sinusoidal voltage with a maximum amplitude of 120 V at t = 0 is applied across the terminals of an inductor. The maximum amplitude of the steady-state current in the inductor is 20 A Part A What is the frequency of the inductor current? Express your answer with the appropriate units. f= Part B Submit Request Answer μÀ 0₁ = Value Submit If the phase angle of the voltage is zero, what is the phase angle of the current? Express your answer with the appropriate units. μA Value Units Request Answer ? Units ?
Let's continue analyzing the RL transient circuit. R 100 VA 10V 811∞ Switch is at A 01A O-1A + VR(t) - 02A Switch is at A O OA t=0 t= 0+ Switch is at B Y t=0 = 0. Note that, the current in the 3. At t = 0+, which is the time instant immediately after t inductor is a continuous value, i.e., it cannot suddenly change. Therefore, IL (0) = I₂ (0¹) vi(t)L 10H 4. At t= too, the switch is at position B. The connection between the voltage source and the inductor has been disconnected for a very long time. What is the current in the inductor at this time, i.e., IL (+∞o)? t = +∞ Switch is at B
NOTE: Solve this as soon as possible, I need this urgently. For the circuit given below, show and explain what is the value of voltage v(t) at steady sate. ww- 10 V (+ v(t) =7F t= 0
I need the answer as soon as possible
1
Problem 06.046 - DEPENDENT MULTI-PART PROBLEM - ASSIGN ALL PARTS Consider the given circuit under dc conditions, where R=15 02. 252 3.А www R + "C2F Find the voltage vc The voltage vc is V. 592 0.5 H NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Problem 06.046.a - Voltage across a capacitor in a R, L, C circuit
A capacitor in an RC circuit with R = 2 Q and C = 1.6 F is being charged. The time required for the capacitor voltage to reach 100 % of its steady state value is: O A. 4 seconds O B. 0.5 seconds O C. 40 seconds O D. 16 seconds O E. None of the given answers O F. 8 seconds A Moving to the next question prevents changes to this answer. Question 5 of 30
(p) Suppose for some arbitrary system: 2 H(s) = 1 20.97 12- 0.97 s+2 - j2 s+2 + j2 Write down h(t), assuming that it is causal. If you think the answer should include sinusoidal terms, your answer must reveal so.