.Consider the following two-port circuit measurements While port 2 open, a voltage of 110 cos(2500t) V is applied to port 1. A current of 32 cos(3000t-43) A is measured into port 1. Port 2 voltage is 98 cos(4000t+25) V With port 2 short-circuited, 40 cos(3800t) V is applied to port 1. The current into port 1 is 1.2 cos(4000t+45)A and the current into port 2 is 0.6 cos(3800t+140) A :The parameter hz1 is 0.89 225° 0.5295° 0.33 Z-68°

.Consider the following two-port circuit measurements While port 2 open, a voltage of 110 cos(2500t) V is applied to port 1. A current of 32 cos(3000t-43) A is measured into port 1. Port 2 voltage is 98 cos(4000t+25) V With port 2 short-circuited, 40 cos(3800t) V is applied to port 1. The current into port 1 is 1.2 cos(4000t+45)A and the current into port 2 is 0.6 cos(3800t+140) A :The parameter hz1 is 0.89 225° 0.5295° 0.33 Z-68°

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For an n-channel MOSFET with tox=15 nm, L= 1.0 um, W = 30 um, Lov=0.05 um, Cao %3D = Cabo = 20 fF, I=2 mA, µnCox = 0.3 mA/V?, Vo = 0.7 V, VSB = 1.2 V, and VDs = 2 V, %3D %3D %3D calculate Cgs, Cab, Cab, and fr.
Solve for the voltage across the collector-base junction for the circuit shown? The dc beta of the transistor is 150.
Please provide solutions for question 3a.ii
Вс Vec - tion that RE Down Consider the transistor Circuit Shown. Let B = 120 and assume that VSE=0.7v. The circuit has the Values shown ert SON NOVANo it tow alt rot gorb not al V8 16 D below soll Disapid Vcc ws() RB RE entt snimnosts a 4701 ard- bzhau sooib شده ماذا inالله .. الرو 97 2001 все ча 4.712 المال 2mur 220 Determine the base Current, Is portion on I Determine the Collector Current, Ic • miesto a Determine the voitage between the collector and emitter VC E 2 Determine the value of RB that sets Vce = 0:31 wt NO
For the fixed-bias network in Figure 2, if the gain is 5, find the following: 1. RD 2. If V;=2mV, find Vo. +VDp (+22 V) Rp Ve Ipss = 8 mA Vp=-2.5 V Yos= 20 µS 10 MQ Figure 2 Maximum size for new files: 100MB Files You can drag and drop files here to add them. Accepted file types All file types
7. Assume that Re in the following figure was replaced with a 3300 resistor. (a) What is the new value of Ic and Vcc? (b) What is the power dissipated in Rc because of this change? (c) What is the power dissipated in the transistor because of this change? RS RB 26 5.1 k +Vcc +18 V O Re 2700 RE 470 Ω -VEE -18 V
Q4. Determine the Y-parameters at a frequency of 100 MHz for the two-port network shown in figure 4. Present your answer in matrix form. →→→H RI R-10 Ohm C3 TC-20 nF C=10pF 1 L1 L-10mH C2 C-100 pF Figure 4 R2 R-5 Ohm C4 TCH OF
Determine IDQ and VGSQ for voltage divider bias configurationfor the JFET using graphical analysis. In addition to obtaining the VD, ?Sand VDS.We have the following data of the different elements of the circuit, such as:R1 = 3.3 MΩ, R2 = 3.3 MΩ, RD = 860 Ω, RS = 2.2 kΩ and powered by one source 12 volts. The manufacturer's sheet indicates that IDSS = 12 mA and VP = −3 V. Include the transfer characteristic graph to obtain the values of thepoint Q.
24V 1. Find the DC collector, emitter current, ré,, ré,? 7.5kn 1.5kN 2. Draw AC circuit & Find the Zi,, Zo,, Ziz, & Zo,? IB1 02 50uF Q1 10kN 3. Find the Ayn1,' AVn,? B1 = 100 4. Draw the two port system and put the AC parameter from item Ic2 = IE, 6.2kN 10uF 2 & 3. Vi Q2 B2 = 100 3.9kN 1kN 100uF
FROM THE SOLVE DIAGRAM FOR A COMBINATIONAL ELEMENT ACCORDING TO THE NOMENCLATURE FOR IT, WITH SAT DATA VCC= 18V, VBE= .47V, VBB = 9V, VCE= .92 V ICSATMAX= 290mA. β= 55 RE= 3.3 OHMS WHAT TOLERANCES DOES THE USE OF CORRESPONDING STANDARDIZED VALUES FOR RB YIELD?
Q2: Derive Zi, Zo, and Av for the n-channel JFET voltage divider circuit. Hint: use the appropriate approximation.
Which of the following is a CDMA standard of second generation network? a) IS-95 b) IS-136 C ) ΕTACS d) EDGE