... 600mm water diameter 300mm 1. diameter 150mm Mercury (SG = 13.6) %3D A venturi meter with diameter of 300mm is attached to a 600mm main pipe and has its axis inclined downward as shown. The manometer shows a deflection of 15cm of mercury (SG =13.6). If the flowing fluid is water and direction is from 1 to 2, determine the a) Discharge if head loss is neglected is Blank 1 cu.m./s b) Discharge if head loss is 500mm from point 1 to 2 is Blank 2 cu.m./s c) Coefficient of discharge is Blank 3

... 600mm water diameter 300mm 1. diameter 150mm Mercury (SG = 13.6) %3D A venturi meter with diameter of 300mm is attached to a 600mm main pipe and has its axis inclined downward as shown. The manometer shows a deflection of 15cm of mercury (SG =13.6). If the flowing fluid is water and direction is from 1 to 2, determine the a) Discharge if head loss is neglected is Blank 1 cu.m./s b) Discharge if head loss is 500mm from point 1 to 2 is Blank 2 cu.m./s c) Coefficient of discharge is Blank 3

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

hsllo
Explain each step please
Please try to solve it within 30 minutes
Q9
1
Question II Liquid of sp.gr and u is in a closed tank with air at pressure measured by a mechanical gauge. It is required to flow this liquid through a piping system connected to a tank as shown in Fig. with a flowrate Q. There are five available pumps with different maximum head which of them is suitable for this system? What power must supply to the pump if its efficiency is n=0.6? Pumps Ahmax-1 (m) Manometer Ahmax2 Ahmax-3 Ahmax-4 Ahmax-5 (m) (m) sp.gr. sp.gr. PAir hi h2 hs (kPa-G) (m) (m) (m) (m) (m) liquid 0.85 0.78 Piping System oil 2595 30 15 20 16 35 60 130 210 (Le/d): (Le/d) d. (poise) (m) (m) (km) (km) (cm) (mm) Elbow Valve 0.8 10.3 0.125 P° (h:)H.Ex. (m) Hig Z2 L1 L2 L4 Q (1/min) (kPa) 0.032 42 12 14 60 200 680 100.95 14 PAir 3 Closed L4 Oil Air h3 hz La L2 hi 21 Liquid H.Ex. Hg
Explain the major and minor losses? Then solve for the parallel pipes system shown below, a pump is placed in line 2 so that 0.142 m³/s will flow through each pipe. Pipe material is cast iron and for each elbow. Find the relation between the head loses hL1 and h12 and estimate the necessary pump head. Water viscosity is μ=1x10-³ Pa.s. Line 1, L-30 m, D= 6 inches Q₁-0.142 m³/s Pump Line 2, L, 30 m, D-3 inches Q-0.142 m/s R
6- Determine the type of flow in the water conveying pipe with a diameter of (20 cm) connected to a Vinguri scale with a neck diameter of (5 cm), where the reading of the manometer connected to the two ends of the scale was (Hg 15 cm). Note that: the density of mercury (gm/cm3 13.6) and the scale constant is 1
A venturi meter is to be installed in a schedule 40, 6-inch line to measure the flow of water. The maximum rate is expected to be 800 gpm at 86°F. A 50-inHg manometer is to be used. Specify the throat diameter of the venturi. The discharge cone angle is 5°.A. 2.38 inB. 2.98 inC. 3.40 inD. 4.50 in
10. Water at 25 °C is transferred 10 m high to the first floor using stainless steel pipes (e = 2 x 10-6 m) with a diameter of 2 cm. If the water leaves through a faucet of diameter 1.3 cm at a flow rate of 8 x 104 m³/s. Determine the required pressure at point 1 (P1) if: a) All viscous effects are ignored b) Only major losses are considered c) All loses are considered (major + minor) Assume that the density and viscosity of water at 25 °C is 997 kg/m and 0.891 x 10-3 kg/m.s, respectively. You can use relevant tables and Moody chart to find the required properties. L=4m L-4 m L= 4 m K, = 2.5 10 m K- 1.5 K, = 0.5 L= 4 m K, 8 Water L=5m L%3D4M
I need answer within 20 minutes please please with my best wishes
Calculate the Flow Rate of water at 5°C through the system below. Q = Flow 3.4 m 700 kPa 30 mm diameter DN 65 mm Schedule 40 Pipe