The continuous beam is loaded as shown in the figure. A and C are roller support while E is a fixed support. Assume that supports do not settle, and El is constant. Using the consistent deformation method, determine the following: a. Reactions at the supports. b. Sketch the shear and moment diagram of the beam. C. Determine the value and location of maximum shear and bending moment of the beam. .. The continuous beam is loaded as shown in the figure. A is a fixed support, while B andC are roller. Assume that supports do not settle, and El is constant. Using the consistent deformationmethod determine the following:a. Reactions at the supports.b. Sketch the shear and moment diagram of the beam.c. Determine the value and location of maximum shear and bending moment of the beam.50kN15 kN/m60 kNABDWith5m5m10mIm

Step 1: Step 2: Step 3: Step 4:

.. The continuous beam is loaded as shown in the figure. A is a fixed support, while B and C are roller. Assume that supports do not settle, and El is constant. Using the consistent deformation method determine the following: a. Reactions at the supports. b. Sketch the shear and moment diagram of the beam. c. Determine the value and location of maximum shear and bending moment of the beam. 50kN 15 kN/m 60 kN A B D With 5m 5m 10m Im

.. The continuous beam is loaded as shown in the figure. A is a fixed support, while B and C are roller. Assume that supports do not settle, and El is constant. Using the consistent deformation method determine the following: a. Reactions at the supports. b. Sketch the shear and moment diagram of the beam. c. Determine the value and location of maximum shear and bending moment of the beam. 50kN 15 kN/m 60 kN A B D With 5m 5m 10m Im

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The cantilever beam is supported by a pin at A and a roller at B. The Shear Force Diagram and Bending Moment Diagram are shown below the Free Body Diagram. The cross section of the beam is also shown. A. State the values of the support/reactions, Force AY and Force BY. Include units. B. Calculate the maximum tension stress in the beam. State the location of the maximum tension stress. C. State the location and value of the maximum compression stress in the beam. D. Calculate the maximum shear stress in the beam. State the location of the maximum shear stress. Ay 5 kN/m 25 kN Beam Cross Section B Ax By D - 2m -- 4m. 4m 25 10 100 mm 30 SFD(KN) 20 100 (KN'm)BMD unu 007
This is a mechanics of material question please show all steps clearly please show the given, what is to be found, and a free body diagram.
A compound shaft consists of brass segment (1) and aluminum segment (2). Segment (1) is a solid brass shaft with an allowable shear stress of 54 MPa. Segment (2) is a solid aluminum shaft with an allowable shear stress of 88 MPa. If a torque of Tc=19200 N-m is applied at C, determine the minimum required diameter of the brass shaft d₁ and the aluminum shaft d2. Tc Answers: d₁ = d₂ = i i (2) C B A mm mm
8 Expansion is an axial deformation. 9 True 10 False The coordinates of centroid locate the ge ometric center of the cross-section of the material.( True False Torsional stress is also known as bending stress.( True False
A snow load transfers the forces shown to the upper joints of the Pratt and Howe roof lattices shown below. Ignoring the horizontal responses on the supports ( \(A x=Ex=0 \)) a) Determine the forces in all members using the joint method. Pratt Roof Truss System: AA A 2 Rods Pull Push CC=5,7 WIDTH (m) x=2 y=3,4 height (m) z=4,2 X 1 BB H 2 y 3 CC G y BB 5 D F X Pratt Roof Truss System SOLUTION: 6 AA E A 4-digit number must be written after the comma. For example 14.7845. Forces (kN) AA=4,2 BB=4,2 A
To determine the state of stress in a solid rod using the principle of superposition. A solid rod has a diameter of e = 50 mm and is subjected to the loading shown. Let a = 190 mm, b= 220 mm, c = 310 mm, d = 220 mm, and P = 3.0 kN. Take point A to be at the top of the circular cross-section. (Figure 1) Figure < 1 of 2 ▼ ▼ Part A - Moment about the x axis at A M₂ = As shown (Figure 2), a cut was made at A to determine the resultant internal loadings. Determine the moment about the x axis, M, Express your answer to three significant figures and include the appropriate units
n=8
A bridge girder AB on a simple span of length L = 25 m supports a distributed load of maximum intensity q at mid-span and minimum intensity g/2 at supports A and B that includes the weight of the girder (see figure). 450 mm 32 mm = 25 m 16 mm- 1800 mm 32 mm 450 mm The girder is constructed of three plates welded to form the cross section shown. Determine the maximum permissible load q (in kN/m) based upon the following. (a) solely based on an allowable bending stress oallew = 110 MPa kN/m (b) solely based on an allowable shear stress Tllow = 50 MPa kN/m (c) accounting for both an allowable bending stress oallow and an allowable shear stress Tallow kN/m