..) A series type ohmmeter, designed to operate with a 9-V battery, the meter movement has an internal resistance of 2000 ohm and requires a current of 100 µA for full scale deflection. The value of R1 is 49KQ. a) calculate the value of R2 required to zero the meter? meter deflection. b) An unknown resistor is connected to the meter causing a 60% Calculate the value of the unknown resistance.

..) A series type ohmmeter, designed to operate with a 9-V battery, the meter movement has an internal resistance of 2000 ohm and requires a current of 100 µA for full scale deflection. The value of R1 is 49KQ. a) calculate the value of R2 required to zero the meter? meter deflection. b) An unknown resistor is connected to the meter causing a 60% Calculate the value of the unknown resistance.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Please i want the answer son as possible
i. Draw a circuit diagram of potentiometer method with naming the components and derived the ratio of the two potentiometer readings. ii. In a measurement of resistance by potentiometer, the voltage drops across resistor under test and across 0.0252 standard resistors were found to be 0.882V and 1.2 V respectively. Determine the value of under test. iii. Write two advantages and disadvantages in Potentiometer method.
The diode starts to conduct when the voltage across it is 0.6 V. Vin is a variable DC voltage source. R1 = 11.6 0 and R2 = 9.8 0. www R1 R2 Va If Vin is increased from zero, at what value of Vin volts will the diode start to conduct. Express your answer accurate to two decimal places.
What minimum value of series resistance is required when three 10-watt, 10-volt, 1000-mA zener diodes are connected in series to obtain a 30-volt regulated output from a 45 volt d.c. power source ? R w E₁-45 V Eo= 30 V ↓
6. Connect the SCR block circuit in Figure 2-10, and place CM switch 6 in the ON position. With the oscilloscope monitoring the anode of Q1 and the multimeter across R4, press S1. From your measurements, you determine that a. the gate is open. b. the anode to cathode is shorted. c. the SCR is working normally. d. R4 decreased in value. www WW 9 4.7K R2 1K 00 R4 2200 Figure 2-10. 6.0 Vdc
A 50 μA basic D'Arsonval movement with an internal resistance of 500 is to be used as a voltmeter. The value of the multiplier resistance required to measure a full-scale voltage range of 0-5 volts is?
For the circuit, the voltage drop for the red LED is 2 volts. (a) Find the voltage drop in Resistor R1 b.) Find the current in Resistor R12 c.) Find the current in Diode D12 d.) Find the power dissipated in Diode D12
Question 4 (a) A PMMC movement with a coil resistance of 25 0 requires 0.8 mA for full scale deflection. Specify: a. The coil voltage required for full scale deflection. b. The shunt resistance required for a 0-1 A ammeter. c. The multiplier resistance required for a 0-10V voltmeter. d. Draw both instruments.
Assuming that the diodes in the circuits of Figure-3 are ideal, utilize voltage divider theorem to simplify the circuits and thus find the values of the labeled current and voltage. Note: please solve within 30 minutes. Avoid plagiarism
Example 3 : Find the current flowing through each of the resistors. iR1,İR2, İR3. Assume Si diodes Vs R, 1 kQ 5 V 500 QS R3 2 kQ
What minimum value of series resistance is required when three 10-watt, 10-volt, 1000-mA zener diodes are connected in series to obtain a 30-volt regulated output from a 45 volt d.c. power source ? R E₁-45 V Eo=30 V ļ O 30 ohm O 15 ohm O 35 ohm O 550hm
2. Will give thumbs up if correct answer thank you!!