. What material is in the cleaver that makes the cutting of the FO cable? Why is it necessary?
Q: A sandwich board advertising sign is constructed as shown in Figure The sign’s mass is 9.50 kg. (a)…
A: FBD of board half part. Mass of each side=9.5/2=4.75 kg
Q: The joints of the human body can be studied as levers, as can be the elbow that appears in the…
A:
Q: 77-kg man stands on his toes by exerting an upward force through the Achilles tendon, as in the…
A:
Q: don't believe this is correct, because the Force is not 12 N throughout, and we must factor in the…
A: Given, mass of the particle, m = 9 kg the time-dependent force experienced by the particle, Fd = 6t…
Q: 5. Calculate the tension in each cable. T A 6. Determine the force (F) 20kg 1. 70 T. Z Fy , тход T…
A:
Q: The 537 kg uniform beam is subjected to the three external loads shown. Compute the force reaction…
A: by draw free body diagram we calculate the net force upon point O and find the value of its .
Q: A 30 m long weightless beam has an 82 kg mass resting on one end and a 64 kg mass on the other end.…
A:
Q: The biceps muscle exerts a muscle force of 1000N on the forearm, as per below. The muscle force acts…
A: Magnitude of muscle force F=1000N Angle made by muscle force with forearm = 300 Hence angle made by…
Q: the long stick with a length(L) and mass(m) supports M. the stick is supported by both tension and…
A: When a body in the system undergoes various forces , the forces need to be balanced in order to…
Q: Two pots habe been sitting on the stove for a while.one pot has a cooper handle and tje other has…
A:
Q: A hydraulic car lift uses a small piston with a cross-sectional area of 2.50 cm² and a large piston…
A: Given that, F1=?A1=2.5 cm2F2=12500 NA2=300 cm2
Q: A 550 ?? drawbridge has a hinge at one end and a cable attached to the other. It is stuck in a…
A:
Q: A 5-m weightless strut, hinged to a wall is used to support a 1189 N block as shown. Determine the…
A: Given Strut length AB = 5 m Weight W = 1189 N Determine the vertical component of the force…
Q: Men are opening a 1,250-kg, 1.75m-wide door (with well-lubricated hinges) by applying to its edge a…
A:
Q: If we assume that the tip of the mandible hits perpendicular to ground, what is the force on the…
A: Given : length, l = 1.30 mm = 1.3 × 10-3 m Mass, m = 130×10-6 g = 1.30 × 10-7 kg Angular…
Q: same direction as from B towards A. Take 0 = 30° %3D 400 lb A В C
A:
Q: The 20kg flowerpot is supported at A by the three cords. (a) Determine the magnitude of the force…
A: Given Flowerpot mass = 20 kg Determine the magnitude of the force acting in cord AB,AC,AD for…
Q: cat is balanced on the edge of a see-saw. The plank of the see-saw is 1m long, and the wedge is…
A:
Step by step
Solved in 2 steps
- A uniform beam of weight 12 N and length 10 m is mounted by a small hinge on a wall. The beam is held in a horizontal position by a vertical rope at the location as shown. What is the hinge force on the beam? 6.0 m O 27 N, up O 27 N, up O zero O 3.0 N, up O 3.0 N, down O 12 N, up O 12 N, downsolve the question given in the image quickly.A UNIFORM ROD OF LENGTH 3M AND WEIGHT 100N, WITH ENDS A ANDB RESTING ON TWO BRACKETS, BEARS 5ØN WEIGHT 0.5M FROM END A AND 150N WEIGHT 2M FROM FIRST WEIGHT. FIND THE REACTION FORCES AT B AND A. FB FA A
- A bolt has a requirement of being tightened to 38Nm. You pull on the end of a 25cm wrench at an angle of 120 degrees.To the radial arm line. What is force of the pull needed?The horizontal beam inFig weighs 190 N, and itscenter of gravity is at its center.Find (a) the tension in the cable and(b) the horizontal and vertical componentsof the force exerted on the beamat the wall.these questions go together they are in parts 1 and 2
- A uniform beam has a length of 17.7 m and a mass of 39.6 kg. The beam is horizontal and resting (in equilibrium) on two supports. One of the supports is located 3.32 m to the right of the beam's center of mass. This support applies an upward force of 245 N to the beam. Ehat distance separates the two supports?What is the force exerted by the cable?Unlike most of the other muscles in our bodies, the masseter muscle in the jaw, as illustrated in the figure, is attached relatively far from the joint, enabling very large forces to be exerted by the back teeth. This is shown in the figure below, where a person is biting down on a bullet placed between the back teeth. (FM = 200 N and r. = 3.7 cm.) M= 2.9 cm Masseter muscle гeaction (a) Using the information in the figure, calculate the magnitude of the force exerted by the teeth on the bullet. (b) Calculate magnitude of the force on the joint.
- A large wood beam weighing 800 N is supported by two potion if and I’m thinking Man weighing 700N where to walk on the overhang portion of the beam how far can he go from point A before the beam tips over?What is the minimum force F needed to lift the piano(mass M) using the pulley apparatus shown in the figure? What is the tension in each four sections?Suppose you're working at an at-home gym and made a simple pulley system to lift a weight with a mass of 25.16 kg. It takes you 2 seconds to complete a rep, lifting the weight to about 0.45 meters. When the cable is under tension, how much force is exerted to complete 1 rep?