. What is the 16-bit binary form of the following instruction? ADD R1, R1, R4

Q: Consider the following MIPS instruction. addi $t5, $t4, - 15 What's the machine code (i.e., 32-bit…

A: Please refer to the following step for the complete solution to the problem above.

Q: e instruction, Add #45,R1 does Adds 45 to the value of Rl and stores it in R1 Adds the value of 45…

A: Add #45, R1 is instruction for addition.

Q: NAME THE INSTRUCTION ONLY that will perform the following function (i.e. ADD,MOV,SUB,..etc.) NOTE:…

A: ADD instruction

Q: What may possibly cause a resumption of the previously completed instruction in the event of a…

A: The instructions that must be followed make up the software that must be run: Pages that are kept in…

Q: Given R= 20, PC = 12 and index register X = 15, show the value of the accumulator for the following…

A: The Answer is

Q: Assume the program starts at memory location 00. Show the RTL statements of the fetchexecute cycle…

A: Actually, the register is a used to store the data or information. MAR,MDR,IR,PC are also type of…

Q: What is right about the ROR instruction? Select one: O a. it rotates the contents of the register…

A: The correct answer of the question is given below

Q: NAME THE INSTRUCTION ONLY that will perform the following function (i.e. ADD,MOV,SUB...etc.) NOTE:…

A: The answer is ADC (Addition with carry)

Q: a. What is the address and size of num1 and num2? b. What is the address of the instruction…

A: As per bartleby guidelines, For multiple questions asked I am allowed to solve only first question.…

Q: 6. What is the result of executing the following instruction MOV AL,05H AND AL, 03H OR AL,01H NOT AL…

A: Assembly language An assembly language is a sort of low-degree programming language that is…

Q: What would cause the current instruction to be reset if there was a problem?

A: Introduction: A page fault is a term used to describe memory pages, and when a user requests that…

Q: What may possibly cause a return to the currently executed instruction in the event of a fault?

A: The program which is to be executed is a set of instructions: Page fault is a phrase that refers to…

Q: Write the instruction that allows for returning from an interrupt call

A: A mechanism in computer systems called an interrupt call, often known as an interrupt, enables…

Q: 2. Suppose Mask = 0x00000F0F and P = 0xDCBADCBA. What is the result of the following bitwise…

A: "Since you have asked multiple question, we will solve the second one for you. If you want any…

Q: What would cause the current instruction to be reset if an error occurred?

A: Usually, at Intel as a minimum, an interrupt is something that comes from the outside global.…

Q: Is the following statement true or false? In von Neumann architecture it is not possible to…

A: The von Neumann architecture is a foundational computer design concept that defines the structure…

Q: Describe the stages involved in the fetch-decode-execute cycle in detail. Your explanation should…

A: Introduction: Fetch-dee-execute cycle steps code-execute cycle is a standard process that describes…

Q: Program Q is loaded into physical memory location 60K by the operating system. a. What is the actual…

A: SUMMARY: - hence, we discussed all the points.

Q: The CPU fetches the instruction from memory according to the value of Select one: a.the status word…

A: The Answer is in step2 As per Bartleby guildlines we did only one question

Q: 3 What are various micro-operations carried out for execution of following instruction. Given PC is…

A: Given,What are various micro-operations carried out for execution of following instruction. Given PC…

Q: Write the instruction that allows for returning from an interrupt call 1

A: In assembly language programming, an interrupt call allows the processor to respond immediately to…

Q: Assign the register numbers for all the variables. You are encouraged to refer the MIPS assembly…

A: The solution to the given question is: Code - Give g and h are in registers $s0 and $s1. Answer (1)…

Q: Assume the following register contents: $t0 = 0x01234567, $t1 = 0x56781234. Set back to these values…

A: The value of $t1, $t2, $t3, $t4 after the above instructions are given below

Q: A register in which of the following that holds the current instruction while it is being executed…

A: Given that, A register in which of the following that holds the current instruction while it is…

Q: The purpose is to convert choose your answer... and the instruction is used in choose your answer...…

A: The purpose of cbw is to convert "the signed value in the AL register into an equivalent 16…

Q: CMP INSTRUCTION HAS THE SAME FUNCTION AS Select one: O a. SUB INSTRUCTION WITHOUT SAVING THE RESULT…

A: CMP instruction The value of Operand2 is subtracted from the value in Rn by the CMP instruction.

Q: Fill in the blank areas in the following table. The memory accesses column should include all memory…

A: The solution is given below with an explanation:

Q: If the user presses a lower case 'a' on the keyboard and the following instruction is executed: GETC…

A: The GETC instruction reads input from the keyboard, and in this case, it captures the ASCII…

Q: 7. For both of the instructions shown below, the initial conditions are shown. The result (which the…

A: Assembly language which refers to the one it is a low-level programming language that communicates…

Q: Which statement is correct for the memory segments in 8086 microprocessor? a. For Stack segment,…

A: The memory segments in the 8086 microprocessor will have the stack point register which will have…

Q: 13. What is the addressing mode used with the second operand in the following instruction: ADD AH,…

A: The different ways in which a source operand is denoted in an instruction is known as addressing…

Q: Here, X=1 Subject : Computer Architecture ( Please give me correct Answer) Thank you.

A: A computer system is basically a machine that simplifies complicated tasks. It should maximize…

Q: Please provide additional context or information about the R, J, and I architectural directions in…

A: This article explores the R, J, and I architectural directions in Instruction Set Architectures…

Q: Fill in the following table showing the results of the indicated instructions, using the register…

A: I have given handwritten solution. see below steps for complete explanation.

Q: Study the following handwritten (potentially buggy) code (you can assume "." refers to code that is…

A: Answer: I have given answer in the handwritten format.

Q: Show the status flags after execution of INC instruction (initially all flags are clear): (b E) CLA)…

A:

Computer Fundamentals

The computer is termed computation. For calculating or computing something the device that has been used is known as the computer. Or we can say that for performing a fast arithmetic operation the device that has been used is a computer. Storing, processing, and retrieving are the main features of a computer.